February 2011 - montgomery_boats - mailman.xmission.com

Re: M_Boats: Video - Havasu Pocket Cruisers Convention!
by TOMMYVAL＠aol.com 24 Feb '11

24 Feb '11

Thanks for sending along, great work looking forward to the rest of em Gary Valetti M17

1 0

rebedding and refinishing
by Kevin Lynch 22 Feb '11

22 Feb '11

Dave, Thanks for your thorough how-to on rebedding deck hardware and refinishing the teak. I plan on doing both as soon as this mountain of snow melts (Boston area). It looks like previous owner used varnish instead of oil on the teak so I probably have a lot of sanding to do. Kevin Lynch M15 #200 Stoughton, MA

3 2

Re: M_Boats: Rebedding deck hardware
by bownez＠juno.com 22 Feb '11

22 Feb '11

Hi Daniel, Another great epoxy supplier is System Three.They offer a starter kit with a variety of materials and instruction manual.Your approach will work well, don't breathe the fumes! It's bad ju-ju.Practice makes perfect when it comes to epoxy. Good Luck, Bones Just back from Sean's bash in Havasu ____________________________________________________________ $65/Hr Job - 25 Openings Part-Time job ($20-$65/hr). Requirements: Home Internet Access http://thirdpartyoffers.juno.com/TGL3141/4d6424d169f005004cast01vuc

1 0

Re: M_Boats: Sliding galley unit?
by Bowman, Jeremy 22 Feb '11

22 Feb '11

Dave, Thanks for the input. I'm not able to take a look at the unit now, but what I was thinking about cutting just the top part off (the part that is taller than the starboard berth) and having just that part slide back; then add hardware into the bottom part to make a seat. However, I have decided that since part of Griselda's beauty is that she was kept in such good condition without major modifications, I should just keep everything as is... just add a water tank and maybe a portable gas burner.

1 0

Re: M_Boats: Retractable OB mount for M-15
by Martha Ekwurtzel 21 Feb '11

21 Feb '11

I wish I had a short shaft for my M 15 motor mount. It is obvious from the specs listed in the motor owner's manual the prop extends several inches too far beyond the bottom of the transom when the mount is in the down position. Perhaps it's a matter of the hieght of the initial positioning of the mount on the transom? Martha Ekwurtzel M 15 "knot head" Lake Koshkonong, WI John Tyner <tynerjr(a)md.metrocast.net> wrote: >Thank you, Connie. Now was that rectangular hatch in the actual seat >(horizontal) or the vertical inner wall aft of the seat? > >I'm also using the Honda 2 HP, but long shaft (I think). > >John Tyner >'88 M-15 #412 "Chimpanzee" > >On 2/21/2011 7:36 PM, Conbert Benneck wrote: >> On 21-Feb-11 12:58 PM, John Tyner wrote: >> >> Hi John, >> >> My M15 #400 originally had the fixed motor mount when I bought it. >> >> LaterI decided to change it to a lift mount - don't recall which one I >> bought,- but to gain access to the transom and add a backup plate, I cut >> out a section at the aft end of the port cockpit seat and installed a >> large rectangular sealing hatch. >> >> This gave me unlimited access to the transom so that it was easy >> installing a backing plate on the inside and later putting on the nuts >> and lock washers after I had installed the lift mount. (I was using a 2 >> HP HONDA short shaft engine). >> >> The advantage of using the large access port is that it gives you added >> - easily accessible - storage space. I used it for my small plastic >> bucket and for cleaning materials. >> >> Connie >> >> ex M15 #400 LEPPO >> >> >> know it's been mentioned several times before, but I've eleven years of >> (incomplete) e-mails from the server I don't want to search through. >>> >>> What's the consensus replacement for the M-15's original fixed motor >>> mount? Garelick has several models. On the lighter (engine HP rating) >>> end, the models 71040 (aluminum) and 71037 (SS) have 8-1/2" of >>> vertical travel. Is this sufficient for an M-15? Or would the heavier >>> (7.5 - 20 HP, 11-1/4" vertical travel) model 71057 (aluminum) or model >>> 71056 (SS) be required? There's also the aluminum model 71042 (7.5 - >>> 12 HP) with 14-1/4" vertical travel. Obviously I'd prefer stainless, >>> and Defender has the model 71037 on closeout, but is the travel >>> sufficient? >>> >>> http://search.defender.com/search.aspx?Action=9&Ascending=True&SH=QT1nYXJlb… >>> >>> >>> And as I am, of course, too large to fit down under the cockpit to get >>> back to the transom (if only I were 17 again!), I've been thinking of >>> adding an access port so I can get to the fasteners. Is a 4" opening >>> sufficient? >>> >>> John Tyner >>> '88 M-15 #412 "Chimpanzee" >>> >>> _______________________________________________ >>> http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats >>> >>> When posting, remember that there is no privacy on the Internet! >>> >> >> >> _______________________________________________ >> http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats >> >> When posting, remember that there is no privacy on the Internet! >> > >_______________________________________________ >http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats > >When posting, remember that there is no privacy on the Internet!

2 1

Re: M_Boats: Rebedding deck hardware
by ndorf＠surfbest.net 21 Feb '11

21 Feb '11

When I reseated my mast step, I drilled the holes a little larger, used a nail to try and clean out any soft wood, then "dammed" the bottom of the holes with duct tape, then used a syringe to dispense penetrating epoxy into the holes. When the epoxy cured, I redrilled to correct original bolt diameter and seated the mast step with 3M 4000 UV. This has worked well for me but YMMV.

2 1

Sliding galley unit?
by Bowman, Jeremy 21 Feb '11

21 Feb '11

I asked about this in a previous post but it was mixed with another subject. I'm interested in altering the galley unit on Griselda. My idea is to use a dremel tool or something to trace around where the galley attaches to the hull, leaving the lower part to build a seating area into. Then i'd like to put the upper part on a track to slide it below the cockpit when I want to use the bunk, or pull it back for using the galley. That way, day sails would be more comfortable with more people, but during extended cruises or overnighting, i could use the galley. Does anyone have any thoughts about this idea?

2 1

Another SAGE 17 video
by W David Scobie 20 Feb '11

20 Feb '11

i have posted another short video of Sage 17 in my Havasu Pocket Cruisers Convention BLOG #7 in the Sage Marine Events and Rendezvous forum - www.sagemarine.us/forum this is an on-boat perspective of her heading to weather. the direct you-tube link is - http://www.youtube.com/watch?v=jMFJs1x3Qzo :: Dave Scobie :: M17 #375 - SWEET PEA - www.m17-375.webs.com :: Sage Marine - www.sagemarine.us

1 0

Sage 17 video
by W David Scobie 18 Feb '11

18 Feb '11

i have posted a short video of Sage 17 in my Havasu Pocket Cruisers Convention BLOG #6 in the Sage Marine Events and Rendezvous forum - www.sagemarine.us/forum :: Dave Scobie :: M17 #375 - SWEET PEA - www.m17-375.webs.com :: Sage Marine - www.sagemarine.us

1 0

thanks and apologies again
by Bowman, Jeremy 16 Feb '11

16 Feb '11

Stan, thanks for the offer. It would be cool to meet someone who possibly helped build Griselda. There aren't any issues I can think of that need work though, Ron and his brother kept her in really, really good shape. The only major alteration I may do in the future is to detach the galley unit from the hull and put it on a slider system so I can push it back under/into the port cockpit locker for more seating area when the galley is not in use. I think I saw a write-up for doing that somewhere once but can't remember where. Dave, thanks for helping me with how to post to the board. I wasn't exactly sure how to do so, and didn't know the rules about pictures. (Sorry!) Eldor, well, it's too bad we can't sail together, but I don't feel too terribly bad...since you get to sail San Juan! That's awesome. Does anyone remember a write up about the movable galley?

2 1