August 2002 - USR-TC - mailman.xmission.com

Upgrade Dsp's
by Terry Kennedy 27 Aug '02

27 Aug '02

When upgrading the code in a dsp 3com once said that the modem should returned to default and then then up for the proper switch type and so on. I have looked through my notes on this and can't find what I am looking for -- under the card level settings, under the software there are a bunch of choices: Restore E1/T1 and modems from default Save E1/T1 and modems to NVRam Restore template 1 config from default Save template 1 config to NVRam Restore template 1 config from NVRam Refresh template 1 from NvRam Refresh template 1 config channels And so on.... While trying to figure out the sequence you are supposed to perform here, I realized I don't have much of an understanding of what these REALLY do. Although I can guess on some of this, what's the difference between retoring the modems to default and restoring the templates from default? Is there a differnce between retoring the NVRAM from default and restoring the template 1 config to default, then loading template 1, then saving to the NVRAM???? Quite confusing. Any info here would be greatly appreciated!! I'll take anything from "here's the link, go read about it" to "don't know what all those really either, but here's the method for setting up the DSP's" to acomplet expanation of templates, default settings and general architecture of the dsp!! Thanks ahead of time. Terry Kennedy OlyPen,

2 2

analog/busy tone/working ok after checking dialtone
by pankaj 27 Aug '02

27 Aug '02

Hi folks, I have nasty senerio, I have many analog lines. 3com(tc1000) Now some of them are behaving nasty. Once or twise user able to login properly in that line. Now in some lines I am geeting busy tone, evenif line is free(i.e no user loged in). Now I unplug that line from modem , and leave it in air, but still I got busy tone on that number, Than I pluged it in to phone-intrument(handset) and than also I got busy tone on that number. now i pickeup the receiver and check the dialtone.Dialtone was ok, after checking dial tone I was able to get ring on that number, and user is also able to login. The same trouble I faced in many lines in three-fine quards-modems. My telco people come and check earthing and all but seems everything ok. Any clue will help me out ?? Thanks pankaj

1 0

HiperArc 5.3.2 vs 5.3.3
by Randy Cosby 23 Aug '02

23 Aug '02

I notice there is a 5.3.3 release of the HiperArc code. I have 5.3.2 on most of my boxes. What are the major difference? I have an ARC that is crashing on me, and wonder if there are any known issues in 5.3.2 that may be fixed in 5.3.3. Sure would be nice to have version release notes somewhere. Randy Cosby Vice President InfoWest, Inc. P: 435-674-0165 x 11 F: 435-674-9654

1 0

caller-id on a Quad modem
by Gen Camiling 22 Aug '02

22 Aug '02

>During connection or after connection? During connection you would have to >depend on the NMC or the ARC to do this for you, no there is no AT command. And i can see this captured ANI via "list dnis" command on the Hiper prompt? Via the TCM will it be displayed on the Performance Monitor - Call Statistics? >After connection you can use ati6 - that will give you the disconnect reason >and ANI/DNIS This holds true for an individual modem, what if i wanted to view the entire modem rack of 60 ports, any Hiper CLI command or script that you have for this? It will be much appreciated =) -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 http://www.imvi.com.ph mailto:gcamiling@imvi.com.ph ==================================

2 1

US robotics total control
by Fred Ebnereza 22 Aug '02

22 Aug '02

I'm trying to get in to NetServer but I don't have a right cable. Please let me know the pin configuration of the cable I should use to configure the system through channel 1. regards Fred Ebnereza Daston Corp 703-288-3200

1 0

anyone using TC100? not 1000
by Stephen Rivera - WRCA.Net 22 Aug '02

22 Aug '02

I have customer looking to move one of these, havent had one before. Anyone interested? TC 100 TC 100-6 Enh BCU Main Memory (1x) MS128 Memory cards (2x) MC64 RP Main Memory (1x) MS64 Card description by location: RMP RM CPU0 RM-CPU(HH)/HBH16-P/D RM IO0 RM-IO(H)/HBH31-L/F RP2 RP-D/HBH26-LD1 NIF4 NE1008TA/HBJ02-M/T NIF5 NAOC3-1M/HBJ08-L/01 POW0 PWU95-BU POW1 PWU95-BU (option) The TC 100 is in mint shape - I think it was used in two or three trade shows. Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

caller-id on a Quad modem
by Gen Camiling 21 Aug '02

21 Aug '02

Is there an AT command on a Quad modem for it to detect or capture ANI into an analog line? The TELCO will provision sending the ANI into the analog line. -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 http://www.imvi.com.ph mailto:gcamiling@imvi.com.ph ==================================

2 1

RE: [USR-TC] Configuring dial-out on TC
by BSmith＠solunet.com 21 Aug '02

21 Aug '02

Patrick, #1 - Create a "modem pool" for dialout add modem_group "name" interface [slot:x/mod[a-b] list modem_groups >>>> This will verify that it was created properly #2 Create your network service for dialout. In your case, this is the one that is actually used on your HiperARC! add network serVICE dialout serVER_TYPE telnetd sock 6666 data "service_type=dialout,modem_group=\"dialout\",auth=off, login_banner=\"You are connnected to a high speed modem Type ate1c0v1 and press ENTER\"" **** Take note of the comma after "auth=off" .. You NEED it there, also, when you paste this into your HiperARC, take out the Return / Linefeed and any additional white spaces. list network services >>>>> Verify that the service has been created #3 Telnet to the port specificed in your service. Thanks, Brian Smith CCNA, NCSA Network Support Engineer SOLUSERVE www.solunet.com 1571 Robert J. Conlan Blvd., Suite 110 Palm Bay, FL 32905 (888)449-5766 fax: (321)-676-1287 -----Original Message----- From: Patrick Ndegwa [mailto:pndegwa@ke.uu.net] Sent: Wednesday, August 07, 2002 6:24 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Configuring dial-out on TC Hi there. I am looking to setup dial-out from a Hiper DSP (through a Hiper ARC ver. 5.3.105) . I would appreciate any assistance on this (even RTMF resources). Cheers, Patrick Ndegwa _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

4 5

Re: [USR-TC] V92 Press Release Offer
by Thomas_Goodman＠3com.com 21 Aug '02

21 Aug '02

Marshall, For any unposted code you will need to open up a Service Ticket with your SCA requesting the code. Posting on the totalservice site will come after the Beta houses approve the code. Tom "Marshall Morgan" <marshall(a)netdoor.com>@mailman.xmission.com on 08/21/2002 02:18:32 AM Please respond to usr-tc(a)mailman.xmission.com Sent by: usr-tc-admin(a)mailman.xmission.com To: <usr-tc(a)mailman.xmission.com> cc: Thomas Goodman/MW/US/3Com Subject: Re: [USR-TC] V92 Press Release Offer Tom, let me know what I need to do. Cindy, I agree ... where can one get this unreleased, working code 3.5.103 (it's not on the website! Arg!) The ARC and NMC code we use is stable but the DSP code has not been (3.5.100, etc). Anyone? Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Cindy Smith" <cindyo(a)ktc.com> To: <usr-tc(a)mailman.xmission.com> Cc: <thomas_goodman(a)3com.com> Sent: Monday, August 12, 2002 11:15 AM Subject: Re: [USR-TC] V92 Press Release Offer > > Question -- Is this code actually good enough to deploy on wide scale. > V.90 was a nightmare for us. We have around 12,000 customers. It took as a > very long time to tweak all the different types of modems with various > strings. Are we now going to have to go back and undo all of that when we > move to V.92? > > We have the contract for the code. We added the memory, replaced the > various cards that needed replacing. I have not upgraded the hubs to the > new code out of fear. Fear of the calls pouring in from customers with > connection issues that will take us months to straighten out. > > Thanks in advance for your insight, > > On Mon, 12 Aug 2002, Thomas_Goodman(a)3com.com wrote: > > > ISPs looking to inform or attract customers about the use of V92 can > > contact me OFF LIST about putting out a Joint Press Release. > > > > > -- > ---------------------------- > Cindy Smith 830-896-1111 > KTC iNet SysAdmin > ---------------------------- > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] Question on Hiper DSP E1/T1 Card
by Shinman, Gilad 21 Aug '02

21 Aug '02

You'll need R2 firmware (HiPer DSP E1/R2 v3.5.12 is in parallel to your code) no hardware changes needed Gilad Shinman Network Engineer Intel Israel gilad.shinman(a)intel.com -----Original Message----- From: Patrick Ndegwa [mailto:pndegwa@ke.uu.net] Sent: Tuesday, August 20, 2002 10:57 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Question on Hiper DSP E1/T1 Card Hi there, I have been running Hiper DSP E1/T1 cards (code ver 3.5.13) for sometime now on ISDN E1 PRI lines. However, my telco provider wants to provision some new R2 E1 lines. I wanted to know if I need to make any hardware or firmware changes on the Hiper DSP cards to support the R2 lines. Cheers, Patrick Ndegwa

2 1