August 2000 - USR-TC - mailman.xmission.com

(usr-tc) Multicast
by Steve Johnson 29 Aug '00

29 Aug '00

I have a USR/3Com Totalcontrol NAS with PRI/T1 cards in it. Does anyone know if these support multicast by default, and if not can someone point me the direction of some documentation on how to turn this on? Also I just setup another one of these boxes, but it wont let me telnet into it, is there something I need to turn on in order to be able to telnet into this box? Thanks -Steve - Steve Johnson - linuxnut(a)sonic.net Sonic.net, Inc. System Administrator 300 B Street #100 707.522.1000 (Voice) Santa Rosa, CA 95404 707.547.2199 (Fax) http://www.sonic.net/ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 11

RE: (usr-tc) Multicast
by Vance McIndoe 29 Aug '00

29 Aug '00

Sorry Brian, I haven't found the HARC's debug of multicast very good at all - it looks like you have covered all the options for the dial-in user - you may even have too much enabled.... > -----Original Message----- > From: Brian [SMTP:signal@shreve.net] > Sent: Tuesday, August 29, 2000 2:13 PM > To: Vance McIndoe > Cc: 'usr-tc(a)lists.xmission.com' > Subject: RE: (usr-tc) Multicast > > On Tue, 29 Aug 2000, Vance McIndoe wrote: > > > Brian, > > > > I think you'll find that the RADIUS attributes, when set, cause changes > to > > the user's modem interface. You can probably use set modem_group all > ...... > > and then do a, save all, to set the same options globally. Remember > this > > wort of change will be visible to the astute dial-in customer though > :-) > > vance, > > I think just setting the defaults like you show below does the trick. I > can observe: > > HiPer>> show ip igmp slot:9/mod:17 > slot:9/mod:17 > Query Interval 125 seconds > Max Response 10 seconds > Version 2 > Querier 208.206.76.40 > Joins 1 > Groups 1 > Robustness 2 > Routing ENABLED > Multicast Forwarding ENABLED > Multicast Proxy ENABLED > IGMP Short Packets 0 > IGMP Bad Checksum 0 > Queries Received 0 > Reports Received 0 > Reports For Known Groups Received 0 > Wrong Version Reports Received 0 > Reports Sent 0 > > > I am dialing in with a pipeline p50. I set multicast forwarding on on > it. But on my linux box behind the pipeline I can't mtrace anything, and > SDR shows nothing. I see the packets going out (the box is configured > correct for multicast because if I connect it on the lan where the total > control is, it works fine: mtrace, sdr, etc) > > Any ideas? I just want to make sure that multicast is working thru the > total control, I would have thought I could mtrace thru the connection. > > Brian > > > > > > Vance > > > > > -----Original Message----- > > > From: Brian [SMTP:signal@shreve.net] > > > Sent: Tuesday, August 29, 2000 11:49 AM > > > To: usr-tc(a)lists.xmission.com > > > Cc: usr-tc(a)xmission.com > > > Subject: Re: (usr-tc) Multicast > > > > > > > > > if a user is configured via radius with no multicast radius options, > but > > > the ARC has the commands below configured, will that user be able to > > > receive multicast? > > > > > > I can add the 5 lines to my ARC's, but don't want to have to add 3 > lines > > > to every users radius profile if I don't have too. > > > > > > At first look it doesn't appear to be working. Is there a "show" or > > > "list" command that will tell me that mutlicast is enabled for a user? > > > > > > I am trying this dialed in, and trying to run SDR but get nothing. I > am > > > using a pipeline which has multicast enabled on it (perhaps the ARC > does > > > not build or forward an SDR cache information?) > > > > > > Brian > > > > > > > > > On Tue, 25 Jul 2000, Antonio Querubin wrote: > > > > > > > On Tue, 25 Jul 2000, Steve Johnson wrote: > > > > > > > > > I have a USR/3Com Totalcontrol NAS with PRI/T1 cards in it. Does > > > anyone > > > > > know if these support multicast by default, and if not can someone > > > point > > > > > me > > > > > the direction of some documentation on how to turn this on? > > > > > > > > You'll need a HiPer ARC router card installed in the chassis to do > > > > multicast. The Netserver router card has no multicast capability. > > > > Multicast is disabled by default on the HiPer ARC. To turn it on > you do > > > > something like: > > > > > > > > set ip multicast proxy interface eth:1 > > > > set ip igmp eth:1 multicast_forwarding enabled > > > > set network user default igmp multicast_forwarding enabled > > > > set network user default igmp multicast_proxy enabled > > > > set network user default igmp routing enabled > > > > > > > > This seems to work for users wishing to receive multicast via > dialup. I > > > > haven't yet tested whether this also allows users to source > multicast > > > via > > > > dialup. > > > > > > > > > > > > > > > > - > > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > > with "unsubscribe usr-tc" in the body of the message. > > > > For information on digests or retrieving files and old messages > send > > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > ----------------------------------------------- > > > Brian Feeny, CCNA, CCDA signal(a)shreve.net > > > Network Administrator > > > ShreveNet Inc. (ASN 11881) > > > > > > > > > - > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > with "unsubscribe usr-tc" in the body of the message. > > > For information on digests or retrieving files and old messages send > > > "help" to the same address. Do not use quotes in your message. > > > > ______________________________________________________________ > > This email has been virus and policy checked by InterConnect Secure's > > Messaging Management System (MMS) product from Tumbleweed > > > > Network ICE "Stop hackers cold!" > > Free download of Black ICE - see just who is interested your PC. > > http://www.interconnect.co.nz/Interconnect/secure/networkice.htm > > ______________________________________________________________ > > > > > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old messages send > > "help" to the same address. Do not use quotes in your message. > > > > ----------------------------------------------- > Brian Feeny, CCNA, CCDA signal(a)shreve.net > Network Administrator > ShreveNet Inc. (ASN 11881) > ______________________________________________________________ This email has been virus and policy checked by InterConnect Secure's Messaging Management System (MMS) product from Tumbleweed Network ICE "Stop hackers cold!" Free download of Black ICE - see just who is interested your PC. http://www.interconnect.co.nz/Interconnect/secure/networkice.htm ______________________________________________________________ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Multicast
by Vance McIndoe 28 Aug '00

28 Aug '00

Brian, I think you'll find that the RADIUS attributes, when set, cause changes to the user's modem interface. You can probably use set modem_group all ...... and then do a, save all, to set the same options globally. Remember this wort of change will be visible to the astute dial-in customer though :-) Vance > -----Original Message----- > From: Brian [SMTP:signal@shreve.net] > Sent: Tuesday, August 29, 2000 11:49 AM > To: usr-tc(a)lists.xmission.com > Cc: usr-tc(a)xmission.com > Subject: Re: (usr-tc) Multicast > > > if a user is configured via radius with no multicast radius options, but > the ARC has the commands below configured, will that user be able to > receive multicast? > > I can add the 5 lines to my ARC's, but don't want to have to add 3 lines > to every users radius profile if I don't have too. > > At first look it doesn't appear to be working. Is there a "show" or > "list" command that will tell me that mutlicast is enabled for a user? > > I am trying this dialed in, and trying to run SDR but get nothing. I am > using a pipeline which has multicast enabled on it (perhaps the ARC does > not build or forward an SDR cache information?) > > Brian > > > On Tue, 25 Jul 2000, Antonio Querubin wrote: > > > On Tue, 25 Jul 2000, Steve Johnson wrote: > > > > > I have a USR/3Com Totalcontrol NAS with PRI/T1 cards in it. Does > anyone > > > know if these support multicast by default, and if not can someone > point > > > me > > > the direction of some documentation on how to turn this on? > > > > You'll need a HiPer ARC router card installed in the chassis to do > > multicast. The Netserver router card has no multicast capability. > > Multicast is disabled by default on the HiPer ARC. To turn it on you do > > something like: > > > > set ip multicast proxy interface eth:1 > > set ip igmp eth:1 multicast_forwarding enabled > > set network user default igmp multicast_forwarding enabled > > set network user default igmp multicast_proxy enabled > > set network user default igmp routing enabled > > > > This seems to work for users wishing to receive multicast via dialup. I > > haven't yet tested whether this also allows users to source multicast > via > > dialup. > > > > > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old messages send > > "help" to the same address. Do not use quotes in your message. > > > > ----------------------------------------------- > Brian Feeny, CCNA, CCDA signal(a)shreve.net > Network Administrator > ShreveNet Inc. (ASN 11881) > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. ______________________________________________________________ This email has been virus and policy checked by InterConnect Secure's Messaging Management System (MMS) product from Tumbleweed Network ICE "Stop hackers cold!" Free download of Black ICE - see just who is interested your PC. http://www.interconnect.co.nz/Interconnect/secure/networkice.htm ______________________________________________________________ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) ARC losing time
by Brian 26 Aug '00

26 Aug '00

Has anyone noticed ARC code 4.1.22 occasionally has its clock freak out and goto a time far in the future like year 2088 or something to that effect? Is this issue fixed in any more recent ARC code? ----------------------------------------------- Brian Feeny, CCNA, CCDA signal(a)shreve.net Network Administrator ShreveNet Inc. (ASN 11881) - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) Filter wildcards
by Pete Ashdown 25 Aug '00

25 Aug '00

I'd like to construct a filter that will stop attempts to send traffic to broadcast and subnet addresses of class C's. In other words *.*.*.0 and *.*.*.255. Any good ideas on this? I don't recall if the TC has any provision for wildcards in filters. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Modem OID
by Blake Fithen 24 Aug '00

24 Aug '00

Hello, does anyone know of an OID to get the number of modems active on an individual Hiper DSP card? TIA, blake - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 6

(usr-tc) Cisco 7206 for sale
by Denis Newkirk 24 Aug '00

24 Aug '00

I still have the USR TC Chassis about to be shut down (sold business). I also have a Cisco 7206 for immediate sale as well as two 1601s with T1 WIC Cards. Please reply direct if anyone is interested. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) HARC upgrade
by Scot Desort 24 Aug '00

24 Aug '00

I'm preparing to upgrade my HARC from 4.1.59 to the 5.0 code. In the release notes, it states that I may have to do an interim upgrade, depending on the flash memory in my HARC. It says to do a sh mem on the HARC to see if I have 8meg or 16 meg. But when I do a sh mem, I get this: Total System Memory Resources: 118418 KB Free Memory: 95516 KB Code Size: 3815 KB Initialized Data Size: 646 KB Uninitialized Data Size: 3844 KB Stack Size: 512 KB So, where does it show the flash memory size? Is it implied at 8 megs (3815 + 646 + 3844)? Anybody know? -- Scot - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

6 12

Re: (usr-tc) problem with packet filter and radius
by Mr DOL 23 Aug '00

23 Aug '00

Did you remove dun/tcp from customer pc then reinstall it? At 02:25 PM 8/23/2000 -0700, you wrote: >I am using a U.S. Robotics Total Control with NETServer Card V.34/ISDN >with Frame Relay V3.3.28. For authentication, I use a RADIUS server, >Livingston RADIUS 2.1 1999/6/23. > >On my Total Control, I have the following filter: > >ct1> show filter filter1 >- IP rules - > 1 permit 0.0.0.0/0 192.150.81.179/32 tcp > 2 permit 192.150.81.179/32 0.0.0.0/0 tcp > 3 deny 0.0.0.0/0 0.0.0.0/0 ip > >I have the following entry in the users file: > >perks4u Password="xxx" > Framed-Protocol = PPP, > Framed-Filter-Id = "filter1", > Framed-Netmask = 255.255.255.255 > User-Service-Type = Framed-User > >When I try to dial in as this user, I get connected, then immediately >disconnected. The following appears in the syslog: > >Aug 23 13:15:05 ct1 acct 02000160 dialnet: port S9 perks4u >succeeded dest 206.43.246.26 >Aug 23 13:15:06 ct1 remote_connect: Packet filter does not >exist. User perks4u disconnected. > >If anyone can shed some light as to why the NAS is claiming that the >filter doesn't exist when it clearly does, that would be appreciated. > >_.,+=~`^"-.,_.,+=~`^"-*.,_.,+=~'`^"-.,_.,+=~`^"-.,_.,+=~`^"- >Jesse Schachter .,. Systems Administrator >The Protosource Network .,. Main Number: (888) 643-8558 ><JSchachter(a)PSNW.COM> .,. Fax: (559) 490-8630 >_.,+=~`^"-.,_.,+=~`^"-.,_.,+=~`^"-.,_.,+*=~`^"-.,_.,+=%~`^"- > > >- > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) problem with packet filter and radius
by Scott Trautman 23 Aug '00

23 Aug '00

You're not matching the filtername. You need both filter1.in filter1.out ...even if one of them is blank. It's looking for filter1.in, your filtername is only filter1 SMT Scott M. Trautman 800-482-4638 Global Dialog Internet 608-240-4638,4637fax 2810 Crossroads, STE LL2 scott(a)gdinet.com Madison WI 53718 http://www.gdinet.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0