October 1999 - USR-TC - mailman.xmission.com

RE: (usr-tc) TCHub and routing
by Robb Bryn 01 Oct '99

01 Oct '99

How does this work if the Network changes each time they logon? The Network in question may be test-ip-I4586 on one logon and test-ip-I4588 the next time? Thanks Robb Bryn > -----Original Message----- > From: owner-usr-tc(a)lists.xmission.com > [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Jim Johnson > Sent: Friday, October 01, 1999 9:05 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) TCHub and routing > > > > set ip network ip2 routing_protocol ripv2 > > Robb Bryn wrote: > > > > I've disabled IP SOURCE_ADDRESS_FILTER allready (no luck). > How do I turn on > > RIPv2 on the arc? > > > > Thanks > > Robb Bryn > > > > > -----Original Message----- > > > From: owner-usr-tc(a)lists.xmission.com > > > [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of > > > Stainforth, Matthew > > > Sent: Friday, October 01, 1999 8:25 AM > > > To: 'usr-tc(a)lists.xmission.com' > > > Subject: RE: (usr-tc) TCHub and routing > > > > > > > > > > > > I believe you'll also want to build static routes or have the > > > ARC advertise > > > the subnet using OSPF or RIPv2 if you want that subnet to be > > > reachable from > > > anywhere other than the ARC itself. > > > > > > Matthew > > > > > > On Friday, October 01, 1999 9:00 AM, Jim Johnson > > > [SMTP:jim@perigee.net] > > > wrote: > > > > > > > > > > > > Make sure you: > > > > > > > > DISABLE IP SOURCE_ADDRESS_FILTER > > > > > > > > if you want the routing to actually **work** as opposed to just > > > > **showing up** in the routing table correctly. > > > > > > > > -Jim > > > > > > > > > Robb Bryn wrote: > > > > > > > > > > I'm configuring my first routed subnet on the TCHub and > > > can't quite > > > > > figure out what I'm doing wrong. > > > > > > > > > > I have a Ascend P50 dialing in via ISDN with radius > attributes of: > > > > > Framed-Address = 208.150.95.241 > > > > > Framed-Route = 208.150.95.240/29 208.150.95.241 1 > > > > > > > > > > After connecting, I can ping the ether address of the TCHub > > > > > (208.133.28.51) from any of the subnet hosts can't ping > > > anything past > > > > > it. I can't ping any host on the subnet from the TCHub. > > > Below is > > > > > the output from the show ip network command. > > > > > > > > > > > > > > > HiPer>> show ip network test-ip-I4586 > > > > > > > > > > SHOW IP NETWORK test-ip-I4586 SETTINGS: > > > > > Interface: slot:14/mod:2 > > > > > Network Address: 208.150.95.241/H > > > > > Frame Type: PPP > > > > > Status: ENABLED > > > > > Reconfigure Needed: FALSE > > > > > Mask: 255.255.255.255 > > > > > Station: 0.0.0.0 > > > > > Broadcast Algorithm: IETF > > > > > Max Reassembly Size: 3464 > > > > > IP Routing Protocol: NONE > > > > > IP Routing Metric: 1 > > > > > RIP Interface Export Metric: 0 > > > > > IP RIP Routing Policies: > > > > > IP RIP Authentication Key: > > > > > HiPer>> > > > > > > > > > > > > > > > > > > > > I'm pulling my hair out trying to figure out what I've > > > done wrong. A > > > > > kick in the right direction would be greatly appreciated. > > > > > > > > > > > > > > > > > > > > Thanks, > > > > > > > > > > Robb Bryn > > > > > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) TCHub and routing
by Stainforth, Matthew 01 Oct '99

01 Oct '99

You'll also have to make sure your router is listening to ripv2 routing updates. On Friday, October 01, 1999 10:05 AM, Jim Johnson [SMTP:jim@perigee.net] wrote: > > set ip network ip2 routing_protocol ripv2 > > Robb Bryn wrote: > > > > I've disabled IP SOURCE_ADDRESS_FILTER allready (no luck). How do I turn > > on > > RIPv2 on the arc? > > > > Thanks > > Robb Bryn > > > > > -----Original Message----- > > > From: owner-usr-tc(a)lists.xmission.com > > > [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of > > > Stainforth, Matthew > > > Sent: Friday, October 01, 1999 8:25 AM > > > To: 'usr-tc(a)lists.xmission.com' > > > Subject: RE: (usr-tc) TCHub and routing > > > > > > > > > > > > I believe you'll also want to build static routes or have the > > > ARC advertise > > > the subnet using OSPF or RIPv2 if you want that subnet to be > > > reachable from > > > anywhere other than the ARC itself. > > > > > > Matthew > > > > > > On Friday, October 01, 1999 9:00 AM, Jim Johnson > > > [SMTP:jim@perigee.net] > > > wrote: > > > > > > > > > > > > Make sure you: > > > > > > > > DISABLE IP SOURCE_ADDRESS_FILTER > > > > > > > > if you want the routing to actually **work** as opposed to just > > > > **showing up** in the routing table correctly. > > > > > > > > -Jim > > > > > > > > > Robb Bryn wrote: > > > > > > > > > > I'm configuring my first routed subnet on the TCHub and > > > can't quite > > > > > figure out what I'm doing wrong. > > > > > > > > > > I have a Ascend P50 dialing in via ISDN with radius attributes of: > > > > > Framed-Address = 208.150.95.241 > > > > > Framed-Route = 208.150.95.240/29 208.150.95.241 1 > > > > > > > > > > After connecting, I can ping the ether address of the TCHub > > > > > (208.133.28.51) from any of the subnet hosts can't ping > > > anything past > > > > > it. I can't ping any host on the subnet from the TCHub. > > > Below is > > > > > the output from the show ip network command. > > > > > > > > > > > > > > > HiPer>> show ip network test-ip-I4586 > > > > > > > > > > SHOW IP NETWORK test-ip-I4586 SETTINGS: > > > > > Interface: slot:14/mod:2 > > > > > Network Address: 208.150.95.241/H > > > > > Frame Type: PPP > > > > > Status: ENABLED > > > > > Reconfigure Needed: FALSE > > > > > Mask: 255.255.255.255 > > > > > Station: 0.0.0.0 > > > > > Broadcast Algorithm: IETF > > > > > Max Reassembly Size: 3464 > > > > > IP Routing Protocol: NONE > > > > > IP Routing Metric: 1 > > > > > RIP Interface Export Metric: 0 > > > > > IP RIP Routing Policies: > > > > > IP RIP Authentication Key: > > > > > HiPer>> > > > > > > > > > > > > > > > > > > > > I'm pulling my hair out trying to figure out what I've > > > done wrong. A > > > > > kick in the right direction would be greatly appreciated. > > > > > > > > > > > > > > > > > > > > Thanks, > > > > > > > > > > Robb Bryn > > > > > > > > - > > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > > with "unsubscribe usr-tc" in the body of the message. > > > > For information on digests or retrieving files and old > > > messages send > > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > > > - > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > with "unsubscribe usr-tc" in the body of the message. > > > For information on digests or retrieving files and old messages send > > > "help" to the same address. Do not use quotes in your message. > > > > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old messages send > > "help" to the same address. Do not use quotes in your message. > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) TCHub and routing
by Robb Bryn 01 Oct '99

01 Oct '99

I've disabled IP SOURCE_ADDRESS_FILTER allready (no luck). How do I turn on RIPv2 on the arc? Thanks Robb Bryn > -----Original Message----- > From: owner-usr-tc(a)lists.xmission.com > [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of > Stainforth, Matthew > Sent: Friday, October 01, 1999 8:25 AM > To: 'usr-tc(a)lists.xmission.com' > Subject: RE: (usr-tc) TCHub and routing > > > > I believe you'll also want to build static routes or have the > ARC advertise > the subnet using OSPF or RIPv2 if you want that subnet to be > reachable from > anywhere other than the ARC itself. > > Matthew > > On Friday, October 01, 1999 9:00 AM, Jim Johnson > [SMTP:jim@perigee.net] > wrote: > > > > > > Make sure you: > > > > DISABLE IP SOURCE_ADDRESS_FILTER > > > > if you want the routing to actually **work** as opposed to just > > **showing up** in the routing table correctly. > > > > -Jim > > > > > Robb Bryn wrote: > > > > > > I'm configuring my first routed subnet on the TCHub and > can't quite > > > figure out what I'm doing wrong. > > > > > > I have a Ascend P50 dialing in via ISDN with radius attributes of: > > > Framed-Address = 208.150.95.241 > > > Framed-Route = 208.150.95.240/29 208.150.95.241 1 > > > > > > After connecting, I can ping the ether address of the TCHub > > > (208.133.28.51) from any of the subnet hosts can't ping > anything past > > > it. I can't ping any host on the subnet from the TCHub. > Below is > > > the output from the show ip network command. > > > > > > > > > HiPer>> show ip network test-ip-I4586 > > > > > > SHOW IP NETWORK test-ip-I4586 SETTINGS: > > > Interface: slot:14/mod:2 > > > Network Address: 208.150.95.241/H > > > Frame Type: PPP > > > Status: ENABLED > > > Reconfigure Needed: FALSE > > > Mask: 255.255.255.255 > > > Station: 0.0.0.0 > > > Broadcast Algorithm: IETF > > > Max Reassembly Size: 3464 > > > IP Routing Protocol: NONE > > > IP Routing Metric: 1 > > > RIP Interface Export Metric: 0 > > > IP RIP Routing Policies: > > > IP RIP Authentication Key: > > > HiPer>> > > > > > > > > > > > > I'm pulling my hair out trying to figure out what I've > done wrong. A > > > kick in the right direction would be greatly appreciated. > > > > > > > > > > > > Thanks, > > > > > > Robb Bryn > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old > messages send > > "help" to the same address. Do not use quotes in your message. > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) TCHub and routing
by Stainforth, Matthew 01 Oct '99

01 Oct '99

I believe you'll also want to build static routes or have the ARC advertise the subnet using OSPF or RIPv2 if you want that subnet to be reachable from anywhere other than the ARC itself. Matthew On Friday, October 01, 1999 9:00 AM, Jim Johnson [SMTP:jim@perigee.net] wrote: > > > Make sure you: > > DISABLE IP SOURCE_ADDRESS_FILTER > > if you want the routing to actually **work** as opposed to just > **showing up** in the routing table correctly. > > -Jim > > > Robb Bryn wrote: > > > > I'm configuring my first routed subnet on the TCHub and can't quite > > figure out what I'm doing wrong. > > > > I have a Ascend P50 dialing in via ISDN with radius attributes of: > > Framed-Address = 208.150.95.241 > > Framed-Route = 208.150.95.240/29 208.150.95.241 1 > > > > After connecting, I can ping the ether address of the TCHub > > (208.133.28.51) from any of the subnet hosts can't ping anything past > > it. I can't ping any host on the subnet from the TCHub. Below is > > the output from the show ip network command. > > > > > > HiPer>> show ip network test-ip-I4586 > > > > SHOW IP NETWORK test-ip-I4586 SETTINGS: > > Interface: slot:14/mod:2 > > Network Address: 208.150.95.241/H > > Frame Type: PPP > > Status: ENABLED > > Reconfigure Needed: FALSE > > Mask: 255.255.255.255 > > Station: 0.0.0.0 > > Broadcast Algorithm: IETF > > Max Reassembly Size: 3464 > > IP Routing Protocol: NONE > > IP Routing Metric: 1 > > RIP Interface Export Metric: 0 > > IP RIP Routing Policies: > > IP RIP Authentication Key: > > HiPer>> > > > > > > > > I'm pulling my hair out trying to figure out what I've done wrong. A > > kick in the right direction would be greatly appreciated. > > > > > > > > Thanks, > > > > Robb Bryn > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) TCHub and routing
by Robb Bryn 01 Oct '99

01 Oct '99

I'm configuring my first routed subnet on the TCHub and can't quite figure out what I'm doing wrong. I have a Ascend P50 dialing in via ISDN with radius attributes of: Framed-Address = 208.150.95.241 Framed-Route = 208.150.95.240/29 208.150.95.241 1 After connecting, I can ping the ether address of the TCHub (208.133.28.51) from any of the subnet hosts can't ping anything past it. I can't ping any host on the subnet from the TCHub. Below is the output from the show ip network command. HiPer>> show ip network test-ip-I4586 SHOW IP NETWORK test-ip-I4586 SETTINGS: Interface: slot:14/mod:2 Network Address: 208.150.95.241/H Frame Type: PPP Status: ENABLED Reconfigure Needed: FALSE Mask: 255.255.255.255 Station: 0.0.0.0 Broadcast Algorithm: IETF Max Reassembly Size: 3464 IP Routing Protocol: NONE IP Routing Metric: 1 RIP Interface Export Metric: 0 IP RIP Routing Policies: IP RIP Authentication Key: HiPer>> I'm pulling my hair out trying to figure out what I've done wrong. A kick in the right direction would be greatly appreciated. Thanks, Robb Bryn

2 1

(usr-tc) using mp/16 at a POP...
by albert 30 Sep '99

30 Sep '99

I have a client that is setting a POP and wants to use a MP/16.. HE has a leased line from point A to point B, the mp/16 is at point B. Can the calls be sent to point A without using a portmaster.?? al. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

Re: (usr-tc) Going nowhere fast...
by eric＠dol.net 30 Sep '99

30 Sep '99

>When you say you got a third box - I understand that you got a USR >Chassis, with a T1 card, modems, nmc and a router card (either Hiper arc >or NETSERVER). From what you say is that the users dial in and they get >authenticated but cannot browse etc, then the problem is on the router >card or on your network. > >May be you are running out of IP address, or maybe the ip address are >overlapping, or you have a problem with arp cache - >So in short looks like our t1 card is fine and you need to take a look at >the routing part of the connection. > I just had the same problem and my ip addresses were over lapping. Check to make sure you did not assign the ips anywhere else in your network. You may have a static route to a customer that you forgot about and the pools is falling into that area. You may have used some of the ips on a web server somewhwere. Start digging in this direction. eric >Delaware Online!.........The SMART Choice! With 56K V.90 & X2 & Flex Modems Phone : 302-762-0375 Fax: 302-762-3462 Failure is NOT an option... - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Quad Digital Modems
by Steve Rivera 30 Sep '99

30 Sep '99

Are the quad digital modems able to handle analog application, as long as nic cards are installed on the chassis. I have customer who is setting up a ISP across seas. He is currently only able to get POT connections, but that is only for now. If he buys the quad digital cards will he ba able to suuport the analog connections now and the digital later. .................................................... Steve Rivera - VP-WR Consultant Associates, Inc. (WRCA) sales(a)wrca.net v-732-833-2111 pgr-732-325-1092 WAN ACCESS SPECIALIST---http://www.wrca.net (CompleteLine Card) Cisco, Ascend,USR,Adtran, Kentrox,Livingston, Microcom,Computone,Verilink IBM,Motorola,UDS,Codex,ATT/Paradyne,Hayes,Racal Datacom,GDC,Telebit MultiTech,Sync/Tylink,Wellfleet,BayNetworks(5399),Black Box,Micom & More - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) Netserver problem
by Blake Fithen 30 Sep '99

30 Sep '99

Had the same problem once. Try reflashing it using PCSDL.EXE. blake > -----Original Message----- > From: Dataheart [mailto:lists@dataheart.net] > Sent: Thursday, September 30, 1999 10:49 AM > To: usr-tc(a)lists.xmission.com > Subject: (usr-tc) Netserver problem > > > Well I'm just full of problems arent I :-D > > I have a Netserver card that once powered up the rn/fl led > flashes green on > and off 13 times, then flashes quickly for a few seconds, > then goes solid green > for a while, then repeast the process. > Anyone know whats going on? > > Thanks, > Aaron > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0