(usr-tc) Channelized T1 vs PRI
Overnight tonight the telco is changing one of our T1s to channelized T1 from PRI service for testing. I seem to remember that there is different code for the dual T1/PRI cards depending on which service you have but I'm using all DSPs now and I can't seem to have any CT1 specific code for these cards on TotalService. Does the one code base now support both CT1 and PRI or am I missing something? Thanks... Matthew - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
On Wed, 22 Sep 1999, Stainforth, Matthew wrote:
Overnight tonight the telco is changing one of our T1s to channelized T1 from PRI service for testing. I seem to remember that there is different code for the dual T1/PRI cards depending on which service you have but I'm using all DSPs now and I can't seem to have any CT1 specific code for these cards on TotalService. Does the one code base now support both CT1 and PRI
yes
or am I missing something?
no - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
You should be able to use the same code for either a PRI or a channelized T1 on the DSP, just go into the TCM, select the T1 portion of the DSP (top LED below the power LED), click Configure-->Programmed Settings-->Trunk Settings You will see a setting called signal mode, it should be set to robbed bit for a channelized T1 and message oriented for a PRI. Unless the telco is changing other things (ie switch type, etc) that should be the only setting you need to change when the telco changes your PRI to a channelized T1. Mike McHenry Systems Administrator MinnNet Communications, Inc. -----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Stainforth, Matthew Sent: Wednesday, September 22, 1999 1:29 PM To: 'usr-tc@lists.xmission.com' Subject: (usr-tc) Channelized T1 vs PRI Overnight tonight the telco is changing one of our T1s to channelized T1 from PRI service for testing. I seem to remember that there is different code for the dual T1/PRI cards depending on which service you have but I'm using all DSPs now and I can't seem to have any CT1 specific code for these cards on TotalService. Does the one code base now support both CT1 and PRI or am I missing something? Thanks... Matthew - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
At 01:46 PM 9/22/99 -0500, you wrote:
You should be able to use the same code for either a PRI or a channelized T1 on the DSP, just go into the TCM, select the T1 portion of the DSP (top LED below the power LED), click Configure-->Programmed Settings-->Trunk Settings
You will see a setting called signal mode, it should be set to robbed bit for a channelized T1 and message oriented for a PRI. Unless the telco is changing other things (ie switch type, etc)
Switch type makes no difference on a CT1
that should be the only setting you need to change when the telco changes your PRI to a channelized T1.
You need to reboot the DSP card, and most likely the ARC card. In our experience, the ARC still shows it as a 23 channel circuit 'till you reboot, then it goes to 24.
Mike McHenry Systems Administrator MinnNet Communications, Inc.
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Stainforth, Matthew Sent: Wednesday, September 22, 1999 1:29 PM To: 'usr-tc@lists.xmission.com' Subject: (usr-tc) Channelized T1 vs PRI
Overnight tonight the telco is changing one of our T1s to channelized T1 from PRI service for testing. I seem to remember that there is different code for the dual T1/PRI cards depending on which service you have but I'm using all DSPs now and I can't seem to have any CT1 specific code for these cards on TotalService. Does the one code base now support both CT1 and PRI or am I missing something?
Thanks...
Matthew
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
--- Clayton Zekelman Managed Network Systems Inc. (MNSi) 875 Ouellette Avenue Windsor, Ontario N9A 4J6 tel. 519-985-8410 fax. 519-258-3009 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
You have to set signeling type from Message Oriented to RobbedBit in TC. Paul D. Farber II Farber Technology Ph. 570-628-5303 Fax 570-628-5545 farber@admin.f-tech.net On Wed, 22 Sep 1999, Stainforth, Matthew wrote:
Overnight tonight the telco is changing one of our T1s to channelized T1 from PRI service for testing. I seem to remember that there is different code for the dual T1/PRI cards depending on which service you have but I'm using all DSPs now and I can't seem to have any CT1 specific code for these cards on TotalService. Does the one code base now support both CT1 and PRI or am I missing something?
Thanks...
Matthew
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (5)
-
Clayton Zekelman -
Mike Andrews -
Mike McHenry -
Paul Farber -
Stainforth, Matthew