RE: [USR-TC] about backup of flash image and dsp's code
Sweetheart - is it really you? Or was this email sent to the wrong address? :-) -----Original Message----- From: Murat Küçük [mailto:muratkucuk@ebim.net] Sent: Saturday, September 28, 2002 9:27 AM To: usr-tc@mailman.xmission.com Subject: RE: [USR-TC] about backup of flash image and dsp's code My love, Honey today on Saturday i want to see you...Please come back home earlier...Please.... İ missed you so much honey... Come please...(l) -----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of ved@iyka.com Sent: Saturday, September 28, 2002 4:20 PM To: usr-tc@mailman.xmission.com Cc: pankaj@worldgatein.net Subject: Re: [USR-TC] about backup of flash image and dsp's code
I am usally saving all config after any changes on ARC. code I mean firmware or flash image if I am not wrong,,, (Like in cisco routers I am saving config as well as IOS using ftp and tftp) Is
there any method to backup and restore config and code of HiperARC using ftp or tftp. So that in case of config loss I just need to restore backedup confige instead of manual reconfiguration of ARC
For the ARC you could do this for all other cards you have to save the code in some place where you can access it later. For the arc there is a configuration option - It is seen when you reboot the arc and you will see for a few seconds a menu that will allow you to specify the a tftp server, code name and other good details. Also you can do this with configuration on the arc - which gives you option to load the code from a tftp server everytime when a reboot occurs or just once (you have options). The command is "set bootrom ip interface eth:1 address .........." This will give you options to configure on how and when to load the code when you reboot the arc. Also the ARC has what is called as a bulk file - you can save the bulkfile and tftp the file to a safe location and then use the bulkfile to reconfigure the arc. For all other cards - configuration is very simple you can use TCM and save the cfm file or nvr file that saves the entire configuration of the chassis to your local pc and then use the same to reconfigure in case of certain bad events occur.
Its ok,,, but can I restore config directly using this text file.
Again how to restore this config,,, or only way is to manual reconfiguration.
Another problem is since from today morning one of my HiperDSP not working,, RN/FL is red, and one of the utilization indicator LED is safrenine, on my TCM card status is ( ?) Unknown.
What do you think happened before this? To start first you would need to reboot the dsp and see if it responds either to nmc or the arc, did you have a hard failure where the dsp lost its brain? -V
Thanks pankaj
-----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of pankaj Sent: Friday, September 27, 2002 7:21 AM To: usr-tc@mailman.xmission.com Subject: [USR-TC] about backup of flash image and dsp's code
Hi All, Here we have frequent electricity problem of overvoltage , and UPS is
also problematic.
Thats why there may be chances of frequent sudden power off.
Will it affect anyway to TC1000, I want to take backup of Code of Hiper ARC and Hiper DSP and NMC,, How?? , so that incase of anything failure I can restore it .. how?? And what else should I take as backup and how?
Please provide me some guidance.
Thanks Pankaj
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Wrong addresssssssssssssssssssssssss :((((((((((((((((((((((((((((((((((((((((((((((((((((((( -----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of Joel - Fox Computers Sent: Saturday, September 28, 2002 8:33 PM To: usr-tc@mailman.xmission.com Subject: RE: [USR-TC] about backup of flash image and dsp's code Sweetheart - is it really you? Or was this email sent to the wrong address? :-) -----Original Message----- From: Murat Küçük [mailto:muratkucuk@ebim.net] Sent: Saturday, September 28, 2002 9:27 AM To: usr-tc@mailman.xmission.com Subject: RE: [USR-TC] about backup of flash image and dsp's code My love, Honey today on Saturday i want to see you...Please come back home earlier...Please.... İ missed you so much honey... Come please...(l) -----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of ved@iyka.com Sent: Saturday, September 28, 2002 4:20 PM To: usr-tc@mailman.xmission.com Cc: pankaj@worldgatein.net Subject: Re: [USR-TC] about backup of flash image and dsp's code
I am usally saving all config after any changes on ARC. code I mean firmware or flash image if I am not wrong,,, (Like in cisco routers I am saving config as well as IOS using ftp and tftp) Is
there any method to backup and restore config and code of HiperARC using ftp or tftp. So that in case of config loss I just need to restore backedup confige instead of manual reconfiguration of ARC
For the ARC you could do this for all other cards you have to save the code in some place where you can access it later. For the arc there is a configuration option - It is seen when you reboot the arc and you will see for a few seconds a menu that will allow you to specify the a tftp server, code name and other good details. Also you can do this with configuration on the arc - which gives you option to load the code from a tftp server everytime when a reboot occurs or just once (you have options). The command is "set bootrom ip interface eth:1 address .........." This will give you options to configure on how and when to load the code when you reboot the arc. Also the ARC has what is called as a bulk file - you can save the bulkfile and tftp the file to a safe location and then use the bulkfile to reconfigure the arc. For all other cards - configuration is very simple you can use TCM and save the cfm file or nvr file that saves the entire configuration of the chassis to your local pc and then use the same to reconfigure in case of certain bad events occur.
Its ok,,, but can I restore config directly using this text file.
Again how to restore this config,,, or only way is to manual reconfiguration.
Another problem is since from today morning one of my HiperDSP not working,, RN/FL is red, and one of the utilization indicator LED is safrenine, on my TCM card status is ( ?) Unknown.
What do you think happened before this? To start first you would need to reboot the dsp and see if it responds either to nmc or the arc, did you have a hard failure where the dsp lost its brain? -V
Thanks pankaj
-----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of pankaj Sent: Friday, September 27, 2002 7:21 AM To: usr-tc@mailman.xmission.com Subject: [USR-TC] about backup of flash image and dsp's code
Hi All, Here we have frequent electricity problem of overvoltage , and UPS is
also problematic.
Thats why there may be chances of frequent sudden power off.
Will it affect anyway to TC1000, I want to take backup of Code of Hiper ARC and Hiper DSP and NMC,, How?? , so that incase of anything failure I can restore it .. how?? And what else should I take as backup and how?
Please provide me some guidance.
Thanks Pankaj
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
participants (2)
-
Joel - Fox Computers -
Murat Küçük