My chassis has two dual 10/100 HiPer Arc nic cards, nmc, 14 HiPer span cards. Is there are way to assign the ethernet ports to specific subnets, with an address pool specific to that port's subnet, and assign certain spans to that ethernet port? In other words.. visually: Slot 15, Ethernet Port #1, subnet A, IP Pool A, Span Cards 1-3 Slot 15, Ethernet Port #2, subnet B, IP Pool B, Span Cards 4-6 Slot 16, Ethernet Port #1, subnet C, IP Pool C, Span Cards 7-9 Slot 16, Ethernet Port #2, subnet D, IP Pool D, Span Cards 10-14 Thanks for the info, -Tom
Tom wrote:
My chassis has two dual 10/100 HiPer Arc nic cards, nmc, 14 HiPer span cards.
Is there are way to assign the ethernet ports to specific subnets, with an address pool specific to that port's subnet, and assign certain spans to that ethernet port?
In other words.. visually:
Slot 15, Ethernet Port #1, subnet A, IP Pool A, Span Cards 1-3 Slot 15, Ethernet Port #2, subnet B, IP Pool B, Span Cards 4-6 Slot 16, Ethernet Port #1, subnet C, IP Pool C, Span Cards 7-9 Slot 16, Ethernet Port #2, subnet D, IP Pool D, Span Cards 10-14
I don't remember any way to do this with just the TC. Keep in mind the TC doesn't have any control over what modem the client dials into. That is between you and your circuit provider. Most commonly this would be handled through a seperate dial pool number. This concerns the span cards portion of the question. You can assign ownership of a modem card to a hiparc something like: set chassis slot 1 owner yes from the hiperarc you want to own it. From the left to the right on your example you could: You could configure each interface with a different ip/subnet. add ip pools a & b to arc on slot 15. set ownership of cards 1-6 for arc on slot 15. assign pool a to users via radius based on username or DNIS. assign a filter to stop routing between the different groups if required Todd might know of a way to do it entirely in the chassis but I don't. -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 Off. 325-691-3301 Cell 325-439-0533 fax 325-695-6841
Hello everyone, Can anyone point me in the direction of finding some literature on the memory requirements for the various software revisions. I've looked in the pdf's for those revisions and I don't see anything regarding the memory requirements, only what revision the other cards should be running at. I'm looking I believe at TCS 4.5 hiperNMC = 8.6.3 hiperARC = 5.3.3 hiperDSP = 3.5.12 Thanks in advance, Todd
Todd, I know that on the Hiper ARC running 5.3.3 you have to have the Hiper ARC with the 128Mb memory on it. Shannan Young sky1@airmail.net www.swdt.com Southwest Data Technology, Inc. 860 N. Dorothy Drive Suite #608 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) THE INFORMATION CONTAINED IN THIS MESSAGE AND ANY ATTACHMENT MAY BE PRIVILEGED, CONFIDENTIAL, PROPRIETARY OR OTHERWISE PROTECTED FROM DISCLOSURE. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution, copying or use of this message and any attachment is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and permanently delete it from your computer and destroy any printout thereof. ----- Original Message ----- From: "Todd" <berto@core.com> To: "'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.'" <usr-tc@mailman.xmission.com> Sent: Tuesday, April 04, 2006 10:15 AM Subject: [USR-TC] Memory Requirements
Hello everyone,
Can anyone point me in the direction of finding some literature on the memory requirements for the various software revisions. I've looked in the pdf's for those revisions and I don't see anything regarding the memory requirements, only what revision the other cards should be running at.
I'm looking I believe at TCS 4.5
hiperNMC = 8.6.3 hiperARC = 5.3.3 hiperDSP = 3.5.12
Thanks in advance,
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Thanks for the reply Shannan. Yea...looks that way to me looking at an existing box. I just wanted to confirm. Todd -----Original Message----- From: Shannan Young [mailto:sky1@airmail.net] Sent: Tuesday, April 04, 2006 11:18 AM To: berto@core.com; Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Memory Requirements Todd, I know that on the Hiper ARC running 5.3.3 you have to have the Hiper ARC with the 128Mb memory on it. Shannan Young sky1@airmail.net www.swdt.com Southwest Data Technology, Inc. 860 N. Dorothy Drive Suite #608 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) THE INFORMATION CONTAINED IN THIS MESSAGE AND ANY ATTACHMENT MAY BE PRIVILEGED, CONFIDENTIAL, PROPRIETARY OR OTHERWISE PROTECTED FROM DISCLOSURE. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution, copying or use of this message and any attachment is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and permanently delete it from your computer and destroy any printout thereof. ----- Original Message ----- From: "Todd" <berto@core.com> To: "'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.'" <usr-tc@mailman.xmission.com> Sent: Tuesday, April 04, 2006 10:15 AM Subject: [USR-TC] Memory Requirements
Hello everyone,
Can anyone point me in the direction of finding some literature on the memory requirements for the various software revisions. I've looked in the pdf's for those revisions and I don't see anything regarding the memory requirements, only what revision the other cards should be running at.
I'm looking I believe at TCS 4.5
hiperNMC = 8.6.3 hiperARC = 5.3.3 hiperDSP = 3.5.12
Thanks in advance,
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Anyone selling 128mb memory for the arcs? Todd -----Original Message----- From: usr-tc-bounces+berto=core.com@mailman.xmission.com [mailto:usr-tc-bounces+berto=core.com@mailman.xmission.com] On Behalf Of Todd Sent: Tuesday, April 04, 2006 11:23 AM To: 'Shannan Young'; 'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.' Subject: RE: [USR-TC] Memory Requirements Thanks for the reply Shannan. Yea...looks that way to me looking at an existing box. I just wanted to confirm. Todd -----Original Message----- From: Shannan Young [mailto:sky1@airmail.net] Sent: Tuesday, April 04, 2006 11:18 AM To: berto@core.com; Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Memory Requirements Todd, I know that on the Hiper ARC running 5.3.3 you have to have the Hiper ARC with the 128Mb memory on it. Shannan Young sky1@airmail.net www.swdt.com Southwest Data Technology, Inc. 860 N. Dorothy Drive Suite #608 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) THE INFORMATION CONTAINED IN THIS MESSAGE AND ANY ATTACHMENT MAY BE PRIVILEGED, CONFIDENTIAL, PROPRIETARY OR OTHERWISE PROTECTED FROM DISCLOSURE. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution, copying or use of this message and any attachment is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and permanently delete it from your computer and destroy any printout thereof. ----- Original Message ----- From: "Todd" <berto@core.com> To: "'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.'" <usr-tc@mailman.xmission.com> Sent: Tuesday, April 04, 2006 10:15 AM Subject: [USR-TC] Memory Requirements
Hello everyone,
Can anyone point me in the direction of finding some literature on the memory requirements for the various software revisions. I've looked in the pdf's for those revisions and I don't see anything regarding the memory requirements, only what revision the other cards should be running at.
I'm looking I believe at TCS 4.5
hiperNMC = 8.6.3 hiperARC = 5.3.3 hiperDSP = 3.5.12
Thanks in advance,
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
participants (4)
-
Lewis Bergman -
Shannan Young -
Todd -
tom＠gigonet.com