Looks to me like a bad NAC. I'd call support for part replacement. -----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Shahrooz Sharghi Sent: Monday, March 07, 2005 12:39 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] e1 pri dsp software download it is exact respons from consol while booting: !!----------> SDL2 for the PPC403 <------------!! __ Enter Download Trigger __ Flash Image Has Valid CRC, Loading Image.... Diagnostic Power-Up Failure Manufacturing Info -> 1AAA13M0 Mode/Env -> 1/0 Fault Code -> 0-142-540-1 Expected Data -> 00000096 Received Data -> 00000000 Text Message -> The Address is the DSP number that failed.----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc@mailman.xmission.com> Sent: Monday, March 07, 2005 9:14 PM Subject: RE: [USR-TC] e1 pri dsp software download
Do you have console access to it? If so plug in and watch the boot process. It should indicate what the error is. If you get a CRC error or corrupt firmware type error, use the aux port to upload new code. Plug in to the aux port with 115200 8 n 1, then reseat the front. After a few moments you should get a prompt, at which time you will need to input the upload command. I believe this is AT{Z1}, but I may be mistaken. Once it is uploaded properly, you'll need to switch back to the console port at 9600. If it's not fixed, you should get a different error. Please let us know what the error is.
-----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Shahrooz Sharghi Sent: Monday, March 07, 2005 10:23 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] e1 pri dsp software download
thanks a lot i placed card in another slot but still has same problem. my tcm is 8.2.6 i think it is not booting fully. how can i repair it?
----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc@mailman.xmission.com> Sent: Monday, March 07, 2005 7:47 PM Subject: RE: [USR-TC] e1 pri dsp software download
If it shows with a ? Then it is not booting fully/properly. Reseat the
both sides of the card and try it again. Remember front out, back out,
back in, front in. Also, it may be that your TCM version is older than
the TCS version of code on your DSP.
-----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf
Of Shahrooz Sharghi Sent: Sunday, March 06, 2005 1:45 PM To: usr-tc@mailman.xmission.com Subject: [USR-TC] e1 pri dsp software download
hi, i want to software download e1 pri dsp card with tcm.(file: he030513.dmf) but i recive this message: "failed, devices are not read yet" in the tcm instead of showing this dsp slot "?" appears. is it possible my card has r2 software?
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
I put it in another TC1000 Chassis and works without problem! ----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc@mailman.xmission.com> Sent: Tuesday, March 08, 2005 12:10 AM Subject: RE: [USR-TC] e1 pri dsp software download
Looks to me like a bad NAC. I'd call support for part replacement.
-----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Shahrooz Sharghi Sent: Monday, March 07, 2005 12:39 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] e1 pri dsp software download
it is exact respons from consol while booting:
!!----------> SDL2 for the PPC403 <------------!!
__ Enter Download Trigger __
Flash Image Has Valid CRC, Loading Image....
Diagnostic Power-Up Failure
Manufacturing Info -> 1AAA13M0 Mode/Env -> 1/0 Fault Code -> 0-142-540-1 Expected Data -> 00000096 Received Data -> 00000000 Text Message -> The Address is the DSP number that failed.----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc@mailman.xmission.com> Sent: Monday, March 07, 2005 9:14 PM Subject: RE: [USR-TC] e1 pri dsp software download
Do you have console access to it? If so plug in and watch the boot process. It should indicate what the error is. If you get a CRC error or corrupt firmware type error, use the aux port to upload new code. Plug in to the aux port with 115200 8 n 1, then reseat the front. After a few moments you should get a prompt, at which time you will need to input the upload command. I believe this is AT{Z1}, but I may be mistaken. Once it is uploaded properly, you'll need to switch back to the console port at 9600. If it's not fixed, you should get a different error. Please let us know what the error is.
-----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Shahrooz Sharghi Sent: Monday, March 07, 2005 10:23 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] e1 pri dsp software download
thanks a lot i placed card in another slot but still has same problem. my tcm is 8.2.6 i think it is not booting fully. how can i repair it?
----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc@mailman.xmission.com> Sent: Monday, March 07, 2005 7:47 PM Subject: RE: [USR-TC] e1 pri dsp software download
If it shows with a ? Then it is not booting fully/properly. Reseat the
both sides of the card and try it again. Remember front out, back out,
back in, front in. Also, it may be that your TCM version is older than
the TCS version of code on your DSP.
-----Original Message----- From: usr-tc-bounces+adam=semo.net@mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf
Of Shahrooz Sharghi Sent: Sunday, March 06, 2005 1:45 PM To: usr-tc@mailman.xmission.com Subject: [USR-TC] e1 pri dsp software download
hi, i want to software download e1 pri dsp card with tcm.(file: he030513.dmf) but i recive this message: "failed, devices are not read yet" in the tcm instead of showing this dsp slot "?" appears. is it possible my card has r2 software?
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
participants (2)
-
Adam Barnhill -
Shahrooz Sharghi