Thanks for prompt reply.

The right most card is "Network Management Card" and the card beside it is "NETserver PRI Card".  "NETserver PRI Card" has a port named "console". I was trying to connect to this port. Am i doing the right thing ?

Do u use yahoo or MSN messenger ? My ID is ahsansimon@yahoo.com and ahsansimon@hotmail.com. If u wish u can add me to ur contact list.

Thanks a lot.

Ahsan

 Joel - Fox Computers <jfox@foxcomputers.com> wrote:

OK - I should have been more specific.  What does it say on the front of the chassis on the card you are trying to connect to?  ie. Hiper Access Router Card, Hiper NMC, Network Management Card, etc.

 

Thanks,

 

Joel

 

 

 

 

-----Original Message-----
From: Ahsan Shariful [mailto:ahsansimon@yahoo.com]
Sent: Monday, February 24, 2003 11:19 PM
To: usr-tc@mailman.xmission.com
Subject: RE: [USR-TC] can't connect to cosole for usr-tc 1000

Thanks for your reply.

The device is USRobotics "Total Contorl Enterprise Network Hub"

Thats what written on the device. I don't have any manual.

I was told that it is a USR TotalControl-1000.

Thanks you

Ahsan

 Joel - Fox Computers <jfox@foxcomputers.com> wrote:

I have no idea on the cable pinout.  But I can help with the jumpers.  What is the device?

-----Original Message-----
From: Ahsan Shariful [mailto:ahsansimon@yahoo.com]
Sent: Monday, February 24, 2003 5:33 AM
To: usr-tc@mailman.xmission.com
Subject: RE: [USR-TC] can't connect to cosole for usr-tc 1000

Thanks for your reply. I'm novice in this field and I might have some mistakes. I would request you to verify what I've done.

1. I'm using a DB9 with RJ45 interface.  So I've made a RJ45 to RJ45 cable. The connecting is as follows:

1-------------6
2-------------4
3-------------1
4-------------5
5-------------3
6-------------2
7-------------7
8-------------8

So the connection is "Console port of usr-tc":RJ45---RJ45:DB9 :"COM port of windows pc"

And I have no idea about the jumper settings as this device is not a brand new one and I don't have any manual or accessories. I got a manual from the web.

Thanks you. Waiting for your reply :-)

Ahsan Simon

 Joel - Fox Computers <jfox@foxcomputers.com> wrote:

The default for the hardware is usually 9600bps, 8-n-1.  If that doesn't work, you can check jumpers on the card you are trying to connect to, but most-likely the cable made is not correct.

 

 

-----Original Message-----
From: Ahsan Shariful [mailto:ahsansimon@yahoo.com]
Sent: Monday, February 24, 2003 2:42 AM
To: usr-tc@mailman.xmission.com
Subject: [USR-TC] can't connect to cosole for usr-tc 1000

Hi,

I need to setup a usr-tc. Hyperterminal can't connect to usr-tc 1000. I'm using a custom cable RJ45 - DB9 ( i got the pinout from this mailing list). I tried with all bits/second (110 to 115200) and other setting as "8-None-1-Hardware". I can't figure out the problem. I don't have the null moded cables or any other cable provied with this hardware.

Somebody please help :-)

Ahsan

---

Do you Yahoo!?
Yahoo! Tax Center - forms, calculators, tips, and more

---

Do you Yahoo!?
Yahoo! Tax Center - forms, calculators, tips, and more

---

Do you Yahoo!?
Yahoo! Tax Center - forms, calculators, tips, and more