May 2005 - USR-TC - mailman.xmission.com

e1 interfaces are down
by Shahrooz Sharghi 31 May '05

31 May '05

I have a TC1000 includes 1 130 Amp PS + 1 hiper NMC + 1 Hiper ARC + 1 E1 DSP (ISDN Code) configuration. in the "List interface" command shows the channels are down: Interface Oper Admin Name Status Status slot:1/mod:1 Down Up slot:1/mod:2 Down Up slot:1/mod:3 Down Up slot:1/mod:4 Down Up slot:1/mod:5 Down Up slot:1/mod:6 Down Up I tested that configuration (exact cards) on 3 different chassis with same result. The only Chassis it shows up up in list interface was one chassis (3com blue) What do you think about my problem? how can I use those cards in other chassis? Thanks a lot

2 1

Anybody sitting on Qty 33.6 Stand alone Sportsters?
by Stephen Rivera - WRCA.Net 27 May '05

27 May '05

Looking for Qty Purchase. If you have some to move please contact me at steverivera(a)wrca.net Sportster 33.6 standalone with power. Thanks. Also looking to buy older 486 EdgeSever cards. NAC alone is fine. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

2 1

Used Gear
by Charles Sprickman 26 May '05

26 May '05

Howdy, We just turned off the last of our dialup gear. I'm looking to unload everything in one shot, any suggestions? Just two TC-1000 racks with the following stuff: rack 1: standard NMC, HiPer ARC, 7 HiPer DSP cards, 2 130A PS rack 2: standard NMC, HiPer ARC, 2 70A PS (this was a backup) And for the collector I've got a boxfull of quad cards, the old NICs with the serial interfaces and a box of quad serial cables. Contact me with any questions... Thanks, Charles ___ Charles Sprickman NetEng/SysAdmin Bway.net - New York's Best Internet - www.bway.net spork(a)bway.net - 212.655.9344

1 0

Which ARC to use?
by Nick Bright 26 May '05

26 May '05

So, I'm getting ready to deploy a new chassis and I'm trying to figure out which ARC card I should use, out of what I have available. I've got three cards with blue handle tabs labeled "ARC Access Router" and one with grey handle tabs labeled "HiPer Access Router Card". http://boberz.thewatch.org/gallery/view_photo.php?set_albumName=album03&id=… http://boberz.thewatch.org/gallery/view_photo.php?set_albumName=album03&id=… http://boberz.thewatch.org/gallery/view_photo.php?set_albumName=album03&id=… http://boberz.thewatch.org/gallery/view_photo.php?set_albumName=album03&id=… Now, according to my understanding the HiPer ARC should be superior. However, my boss was telling me the other day that stuff with the blue handles was newer/better than stuff with the grey handles. So, I'm a little confused as to which card would be better to use. I'm going to be coupling this with an older model NMC, I'm unsure of the model, but It's got a 486SX processor, 20Mb RAM, and 8Mb flash - definately not the newer G3 unit. The chassis will also have seven single span T1 modem cards, too. As an aside, if anyone knows how to take care of the bad flash issue on the G3 based NMC's, without needing a support contract, let me know :) So, which ARC would be my best bet? Thanks in advance for any advice. - Nick Bright Terraworld, Inc

1 0

IP System Host Address not reporting correctly
by Nick Bright 25 May '05

25 May '05

Greetings! I am having a slight problem with a TC1000 chassis I'm trying to put back into service. This chassis was in service about a year ago, and we had no problems with it. I've reconfigured all of the IP interfaces according to the documentation, but in the RADIUS accounting packets the NAS-IP-Address and NAS-Identifier fields are reporting an IP address which is no longer on the system (the IP from when the unit was previously deployed). Upon checking the tech support documents at utstar.custhelp.com I found this: ---- snip ---- Question: How can I set the "IP System Host Address" on a HARC card ? Answer: This parameter is defined by the operating system itself, and it is related to the first IP address that is assigned to an interface on the HARC card, there is no way it can be configured manually. In order for you to change it, it is necessary to disable and remove all the other interfaces but the one that you wish to be assigned as the "IP System Host Address". Once all the interfaces but the one you want are removed, the system will assign it automaticaly. The next step then is to add back the IP addresses you removed to their original interfaces, ans save all the changes. ---- snip ---- This seems to make sense, except I have no other interfaces to remove. Only one IP address is defined (on eth:1), eth:2 is administratively down (and has no addresses assigned). The NMC has an IP, but I think that this is unrelated (it's also completely different from the IP showing up as the IP System host address). I'm not sure where to procede, as I am not an expert with these devices. Anyone have any advice as to what to try to get the correct IP to be reported? Everything works fine on the chassis, except the RADIUS accounting data is reported incorrectly. Any comments, advice, or things to try are appreciated. Some system information that might help: HiperARC Hardware Revision: 21.0.0 HiperARC Software Revision: 5.3.2 NMC Hardware Revision: 3.0 NMC Software Revision: 8.7.3 -- - Nick Bright Terraworld, Inc 888-332-1616 x315 http://home.terraworld.net

2 8

Hiper NMC "priced to move"
by Stephen Rivera - WRCA.Net 19 May '05

19 May '05

In Stock, looking to move some. Qty 20 Hiper NMC (69-3440-00) Complete card set NAC/NIC $250ea 90 day warranty. Steve Rivera -WR Consultant Associates, Inc. T: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

WTB: 130A DC power sets.
by Stephen Rivera - WRCA.Net 18 May '05

18 May '05

Anybody got any available? Also looking for more Quad modem fan out cables. Look forward to your response. Steve Rivera -WR Consultant Associates, Inc. T: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

2 1

hiper arc problem
by Shahrooz Sharghi 16 May '05

16 May '05

hiper access can't ping or resolve the internet (outside of lan), we can telnet to it from same lan. ip routing and gateway don't have any problem.(if we set hiper arc ip address on a pc in lan it can brows internet) any idea?

1 0

hiper arc gateway
by Shahrooz Sharghi 04 May '05

04 May '05

Hi, I want to know how can I set 2 default gateway on a hiper ARC. I want to define two ip network and assign different default gateway for each of them.

2 1