March 2005 - USR-TC - mailman.xmission.com

Anybody sitting on Qty 33.6 Stand alone Sportsters?
by Stephen Rivera - WRCA.Net 27 May '05

27 May '05

Looking for Qty Purchase. If you have some to move please contact me at steverivera(a)wrca.net Sportster 33.6 standalone with power. Thanks. Also looking to buy older 486 EdgeSever cards. NAC alone is fine. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

2 1

Anyone have Dual E1/PRI NIC's available?
by Stephen Rivera - WRCA.Net 30 Mar '05

30 Mar '05

I know they are scarce, but I am hopeful. Anyone have the Dual E1 nic. Not Dual T1/E1 nic - for some reason never get the E1 circuit up with these nics. Let me know if you have any available I give you an offer and pay freight in. Thanks Also still buying 130A DC power sets (PSU/PSI)- paying $150ea Let me know if you have any available. Steve Rivera -WR Consultant Associates, Inc. T: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

Dual 386 T1/PRI card
by Hatcher 25 Mar '05

25 Mar '05

I have two Dual T1/PRI cards that currently have 3.0.2 on them. I want to run Channelized T1, and the install guide says that Channelized T1 is only available with version 4.0 or later. How do I go about getting the software to upgrade the card? Thanks Hatcher

1 0

WTS: E1/PRI- T1/PRI- DSP's and bundles
by Stephen Rivera - WRCA.Net 25 Mar '05

25 Mar '05

Hey guys. These just in. Pricing should be better for you guys that always contact me for E1 cards. I know it doesnt compare to the T1/PRI's but the markets are different and the T1's are all over the place where the E1's are much harder to locate. 1- TC1000 dual 130amp power, Hiper Arc, 4 E1 DSPs, 120 ports $2495 6- Hiper DSP E1 (30 channel modem card set) $500 Qty - Hiper DSP (24 channel modem cad set) $50ea Qty TC1000 336 port T1/PRI Bundles $595 chassis, dual 130a, hnmc, 2x harc, 14-dsp Qty Hiper ARC $125 In Stock. FOB: NJ anything TC1000, I got it. email for further info or parts you need that arent listed. Steve Rivera -WR Consultant Associates, Inc. T: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

WTB: 3Com TC1000 Power Sets and EdgeServer Cards
by Stephen Rivera - WRCA.Net 18 Mar '05

18 Mar '05

Immediate need for the following. EdgeServer Carc AMD K-3 400 MHZ PN# 69-001825-00 DC 130A power sets PN# 69-001404-00 Steve Rivera -WR Consultant Associates, Inc. T: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

reverse telnet
by Vegard Svanberg 15 Mar '05

15 Mar '05

The USR TC's are capable of interfacing the modems over a telnet connection, or so-called reverse telnet. UTstar describes how to get this going, for instance: <quote> 1. set modem s(port#) active 2. set s(port#) login network dialin device /dev/network 3. set s(port#) service_dev telnet 6001 (or any telnet port) 4. set s(port#) service_login telnet 5. save s(port#) or save all 6. reset s(port#) or reset all >From the PC on the network telnet x.x.x.x (netserver ip address) 6001 You can now type AT commands </quote> Connecting to the Netserver ('telnet x.x.x.x xxxx') works, but any typed characters seem to end up in a black hole. Nothing is echoed back, and typing stuff like ATIx etc triggers no response, either. Dip switch tweaking needed? Ideas? -- -o) Vegard Svanberg, CTO - XOIP Comm. (www.xoip.no) /\\ Violgata 3A, N-1776 HALDEN, NORWAY _\_v Phone: (+47) 69701802 | Fax: (+47) 69701801

2 1

USR TC, dead Netserver PRI card?
by Vegard Svanberg 15 Mar '05

15 Mar '05

We recently aquired two 3com/USR Total Control (network hub) with the quad modem cards. Both units are equipped like this: 1 T1/PRI card (NIC: RS-232 + span 1 + span 2) 12 quad modem cards (digital, no NICs) 1 Netserver PRI card (NIC: RS-232 + ethernet 1 + ethernet 2) 1 NMC (NIC: RS-232/EIA561 (CH1+2) + BNC/AUI/ethernet) Issue #1: On the Netserver PRI card, the RN/FL and LAN/TX leds are solid red, always. In TCM, the NAC isn't recognized at all (question mark). We tried to do a firmware upgrade, but pcsdl doesn't connect (all dip switches are off). Sometimes, if we boot the rack while pcsdl is trying to connect, the RN/FL will blink green about 10 times, then all the leds are shut off. It seems to only happen after we've physically re-seated the NAC/NIC, though. We try to flash it with li030421.sdl/li030534.nac. This may of course be a hardware problem, but the problem is on two totally separate units. Issue #2: Because of #1, we wanted to try upgrading the NMC. We only find <filename>.dmf files lying around, and TMC doesn't seem to like that file extension (configuration->software download only seem to accept .nac files). Any clues? UTstar didn't even respond when we asked them about their support rates/contracts. :/ -- -o) Vegard Svanberg, CTO - XOIP Comm. (www.xoip.no) /\\ Violgata 3A, N-1776 HALDEN, NORWAY _\_v Phone: (+47) 69701802 | Fax: (+47) 69701801

1 1

overlap
by Sherwin T 15 Mar '05

15 Mar '05

Hi! some users were encountered carrier loss during or while connected. with this, the usage w/ carrier loss encounter an overlap connection becaue the ras was not able to send a termination request to the radius. does anyone encounter with this kind of problem? pls advise. thanks,

1 0

RE: [USR-TC] e1 pri dsp software download
by Adam Barnhill 14 Mar '05

14 Mar '05

Looks to me like a bad NAC. I'd call support for part replacement. -----Original Message----- From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Shahrooz Sharghi Sent: Monday, March 07, 2005 12:39 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] e1 pri dsp software download it is exact respons from consol while booting: !!----------> SDL2 for the PPC403 <------------!! __ Enter Download Trigger __ Flash Image Has Valid CRC, Loading Image.... Diagnostic Power-Up Failure Manufacturing Info -> 1AAA13M0 Mode/Env -> 1/0 Fault Code -> 0-142-540-1 Expected Data -> 00000096 Received Data -> 00000000 Text Message -> The Address is the DSP number that failed.----- Original Message ----- From: "Adam Barnhill" <adam(a)semo.net> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc(a)mailman.xmission.com> Sent: Monday, March 07, 2005 9:14 PM Subject: RE: [USR-TC] e1 pri dsp software download > Do you have console access to it? If so plug in and watch the boot > process. It should indicate what the error is. If you get a CRC error > or corrupt firmware type error, use the aux port to upload new code. > Plug in to the aux port with 115200 8 n 1, then reseat the front. > After a few moments you should get a prompt, at which time you will > need to input the upload command. I believe this is AT{Z1}, but I may > be mistaken. Once it is uploaded properly, you'll need to switch back > to the console port at 9600. If it's not fixed, you should get a > different error. Please let us know what the error is. > > > -----Original Message----- > From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com > [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf > Of Shahrooz Sharghi > Sent: Monday, March 07, 2005 10:23 AM > To: Discussion relating to the 3Com/US Robotics Total Control > modemsystems. > Subject: Re: [USR-TC] e1 pri dsp software download > > > thanks a lot > i placed card in another slot but still has same problem. > my tcm is 8.2.6 > i think it is not booting fully. how can i repair it? > > ----- Original Message ----- > From: "Adam Barnhill" <adam(a)semo.net> > To: "Discussion relating to the 3Com/US Robotics Total Control > modemsystems." <usr-tc(a)mailman.xmission.com> > Sent: Monday, March 07, 2005 7:47 PM > Subject: RE: [USR-TC] e1 pri dsp software download > > > > If it shows with a ? Then it is not booting fully/properly. Reseat > > the > > > both sides of the card and try it again. Remember front out, back > > out, > > > back in, front in. Also, it may be that your TCM version is older > > than > > > the TCS version of code on your DSP. > > > > -----Original Message----- > > From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com > > [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf > > Of Shahrooz Sharghi > > Sent: Sunday, March 06, 2005 1:45 PM > > To: usr-tc(a)mailman.xmission.com > > Subject: [USR-TC] e1 pri dsp software download > > > > > > hi, i want to software download e1 pri dsp card with tcm.(file: > > he030513.dmf) but i recive this message: > > "failed, devices are not read yet" > > in the tcm instead of showing this dsp slot "?" appears. is it > > possible my card has r2 software? > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

hiper arc consol
by Shahrooz Sharghi 14 Mar '05

14 Mar '05

i have a correct consol cable, it works with NMC or Netserver card. but it doesn't work with hiperarc, card jumpers is set for 9600 and i try 9600,19200,57600,115200 but still doesn't work. what do you think about problem?

2 2