November 2004 - USR-TC - mailman.xmission.com

RE: Busy signal!!!
by Kirti S. Bajwa 24 Nov '04

24 Nov '04

Hello List: I finally got 3Com box (1-HiPer NMC, 2-Hiper ARC & 10-Hiper DSP) setup. Today, I connected a T1-PRI ISDN line to test. But as soon as I connect, the line gives busy signal. What setting causes this. /Please Help/. Thank you in advance. Kirti

2 1

Faxing???
by Dev 24 Nov '04

24 Nov '04

Hello all, Is it possible to setup a 3 COM Quad V.34 Digital-Analog Modem to have one of its lines to do faxing from a linux server and if so where do I want to look for more information on configuring the service. I am looking at using HylaFAX for the server side aspect. ---------- UMPA Brian C. Doyle Director, Internet Services United Merchant Processing Association <http://www.umpa-us.com>http://www.umpa-us.com 1-800-555-9665 ext 212

1 0

mibs?
by S H A N 24 Nov '04

24 Nov '04

hi, does anyone know where can i download the mibs? rgds, -- "Those who Know they do not Know that to Know is to Know what they do not Know!" -Ali Sina

2 1

RE: [USR-TC] D-Channel Down on HiperDSP Multispan (on second/thirdspans)
by Adam Barnhill 24 Nov '04

24 Nov '04

This is probably a stupid question, but are you reconfiguring SPANs 2 and 3 for D channels? Also, does it break in SPAN 4 as well? I have used D channels on 1 and 4. I don't recall if I ever tried it on SPAN 2 or 3. If this is an NFAS setup, you will need to save and reboot for the changes to take effect properly. Also if it is NFAS, make sure you have your Device/Group setup as the TELCO specified. NFAS primary/backup D channel designation is ARC controlled. I also found that sometimes when a D won't come up you can throw it in lineloop a second or two and then drop the loop to bring it up. Along the same lines, in NFAS you can ask the telco to drop the NFAS group and bring it back up. -----Original Message----- From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Lewis Bergman Sent: Thursday, October 21, 2004 7:41 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] D-Channel Down on HiperDSP Multispan (on second/thirdspans) S H A N wrote: > hi, > > i am experiencing the following problem. > > - in a HiperDSP Multispan nic when i use the first span the > d-channel comes up nicely and i am able to connect and surf... > > but whenever, i try to swing the same line from first span to > second/thrid span on the nic the nac always have a d-channel > alarm.. and gives me fast busy tone on dialin. > > any suggestions/ideas would be more then welcome. Since I have never even seen a multispan DSP much less used one I have absolutely no idea and any thing I might say may be discounted as the ravings of a lunatic. Having said that, Are all the span ports occupied or are you trying to do this with only one? If only one maybe the DSP expects to see the D channel on the first port and not on any of the rest? Like I said, no idea. -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 325-691-3301 800-299-6962 _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

Multi IP pool Service
by jswoo 21 Nov '04

21 Nov '04

How to setting Hiper ARC for International/Domestic service simultaneously We want to use one TCH chassis with 2 ARC by 1 telephone number for internet service International link (Public) and Domestic(Private) link only. We have International ip pool and Domestic ip pool also have two different Radius Server for authentication. For internet service for international Modem Users connect as their ID (international) -> each ID get authentication from Radius Server(international) -> get ip address from International ip pool -> use internet service International link For internet service for domestic only Modem Users connect as their ID (domestic only) -> each ID get authentication from Radius Server(domestic) -> get ip address from domestic ip pool -> use internet service domestic link International ip pool : 203.144.218.1/24 size 240 Domestic ip pool : 192.168.10.1/25 size 120 International Radius Server : 203.144.34.173 Port 1645 secret radsecret Domestic Radius Server : 203.144.34.174 Port 1645 secret radsecret Hiper ARC Version : 5.7.2 Thank you so much.

1 0

Help Me! MRTG Setting
by jswoo 19 Nov '04

19 Nov '04

Dear guys. When I make MRTG for connect users of TCH 1000 I set in CFG file as below Target[tch]: 1.3.6.1.4.1.429.4.2.1.10.0&1.3.6.1.4.1.429.4.2.1.10.0 and it shoes all connect users in chassis. How can split for each slots not total chassis for MRTG? For example, only available 1st slot, 2nd slot, 3rd slot or 1st ~ 5th slots etc.... How can change the setting in CFG file for each slots that I want for connection users MRTG. Please help me ! Thanks a lot. Mr, Woo : jswoo(a)thaiit.com

1 0

Need help with HiperDSP and Netservers.
by RKML Mail List 16 Nov '04

16 Nov '04

Hello, We are in dire need of some assistance in configuring our HiperDSP cards with Netservers. Here is the issue. Our Telco is using AT&T 5ESS Switches in NI2 mode. We have 3 HiperDSPs 8mb dram/2mb flash(v.3.5.12) with 1 Netserver 16mb dram/4mb flash(v.3.8.1) and HiperNMC 16mb dram/flash(v.8.6.3) We have been unsuccessful in establishing more than 1 HiperDSP getting it functional with our Telco. The first DSP hands all calls without any problems however when it starts to go to the next PRI span however, the line picks up and then hangs up immediately. Our telco is saying that our equipment is doing this. We have tried rebuilding our circuit from scratch and still the last 2 DSPs just drop the calls. I have the startslot set to 1 with the 3 DSPs in the first 3 slots. Slot 4 is the Netserver. All 72 modems are Active, Ready and waiting for calls in the Netserver. Anyone experienced such a problem? Any solution to fixing this? If anyone can assist, I would greatly appreciate it. Thank you Rudy K.

4 3

3Com 333NMC/ARC/MultiSpan Bundle
by Stephen Rivera - WRCA.Net 16 Nov '04

16 Nov '04

Just into stock today, checking to see if anyone is interested. Mint Condition- TC1000 Chassis with Dual 130A power 333NMC (3C0504218-00) ARC (3C0504693-00) MultiSpan 96 (3C0504222-00) $3500.00 Qty of the Hiper DSP's at $50ea Qty of the Hiper ARC at $75 333NMC set $1250 336 Port v92 Hiper bundles- EMAIL ME, We'll work a price. my new url for TC1000 gear, http://tc1000-nmc-dsp-arc.com/ Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

Lost Total Control Software.
by RKML Mail List 11 Nov '04

11 Nov '04

Hello all, I was wondering if anyone can help me. I am in need of the following files as the HD that I had the files stored on went dead and is unretrievable. The files are - v92.exe (V.92 upgrade code) - HD305109.ZIP - HD30512.ZIP - NE0503110.ZIP - NE050303.ZIP - HARM2206.ZIP - HM080603.ZIP - TCM080206.ZIP Thanks in advance if anyone can help me out. Rudy K.

1 0

Accounting message
by Sherwin T 10 Nov '04

10 Nov '04

Hi! Does anyone knows how to disable the Accounting ON message? --------------------------------------------------------------------- Source-IP Src-Port Destination-IP Dest-Port Id Packet-Type --------------------------------------------------------------------- 192.168.39.152 1646 210.2.230.5 1646 45 Accounting-Request --------------------------------------------------------------------- Time Stamp : 11-NOV-2004 07:03:55 --------------------------------------------------------------------- Acct-Status-Type : 7 Acct-Delay-Time : 157500 Acct-Session-Id : This is an Accounting ON message NAS-IP-Address : 192.168.39.152 thanks, sherwin

1 0