November 2002 - USR-TC - mailman.xmission.com

RE: (usr-tc) NMC not responding
by Mark E. Levy 06 May '03

06 May '03

I;ve had this happen a few times. Just reboot the NMC card by sliding it out if the chassis or via the console interface and it will be well again (until next time). Rebooting the NMC won't affect active users sessions. --------------------------------------------------------------------- Mark E. Levy, President FSInet, Inc. | System Management Associates, Inc. 800-827-6085 x202 | 847-291-1550 x202 847-753-6832 fax | 847-291-3866 fax www.fsi.net | www.sysman-inc.com mark(a)fsi.net | levy(a)sysman-inc.com --------------------------------------------------------------------- > -----Original Message----- > From: Jeff Mcadams [mailto:jeffm@iglou.com] > Sent: Friday, June 08, 2001 9:51 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) NMC not responding > > > Also sprach Kirk Mitchell > > My NMC recently stopped responding to SNMP queries, etc and I'm > >unable to access it via TCM. It has, however, not seemed to affect > >anything as far as dial-up, routing, etc. Other than the fact that I > >can't run MRTG against it or the badmodems.pl script, there's no > >indication that it's having problems. > > Not surprising. The NMC does not have anything to do with the routine > actions of taking and handling calls...it is what it says it > is...purely > a management card. You can totally remove the NMC and not lose any of > the actual *production* functionality of the chassis. > > > Has the card gone bad...need replaced, lost something in part of > >config? How do I go about finding/fixing the problem? > > Proly just needs a reboot, or possibly a reconfig...I've had > a few lose > some of the config (including IP addresses and stuff), and a reconfig > from console (takes me about 30 seconds these days) gets them > fully back > up and running (sucks if its a remote city though). > -- > Jeff McAdams Email: jeffm(a)iglou.com > Head Network Administrator Voice: (502) 966-3848 > IgLou Internet Services (800) 436-4456 > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

RE: [USR-TC] Problem with HiperDSP card
by SWujek＠solunet.com 22 Apr '03

22 Apr '03

Hi Scot, We see this a lot on Hiper DSP cards when they fail. Try the Z-Modem procedure through the console port to reload code to it and see if that works. Most of the cards we see like this have to be sent back to 3Com for repair. Thanks, Steve Solunet TAC -----Original Message----- From: Scot Desort [mailto:scot@njaccess.net] Sent: Tuesday, June 04, 2002 10:09 AM To: usr-tc(a)lists.xmission.com Subject: [USR-TC] Problem with HiperDSP card I have a HiperDSP card in a TC chassis that appears to have failed over the weekend. The RN/FL light was red, and the FOURTH utilization bar LED from the bottom was AMBER. I moved the card to another slot, and it worked OK for 2 days, and failed again. I left the card unplugged overnight, and plugged it back into the same slot this morning. It is now working again. But obviously something is wrong. I know that a red RN/FL is no good, but does the 4th utilization bar being amber mean anything? Any tests or settings I should check while the card is in an operational state? Not ever having a DSL go bad on me, what is the best course of action -- attempt to have Commworks repair it, replace it with a used card, ??? Card is about 2.5 years old. Thanks, Scot _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 2

RE: [USR-TC] Forcing a default route for customer through radius
by Brian Becker 13 Feb '03

13 Feb '03

I was hoping to do it by Radius though. Isn't there a way to do it by framed-route or something like that? Brian Becker President, Poplar Bluff Internet, Inc. http://semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114 -----Original Message----- From: usr-tc-admin(a)mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of Jeff Mcadams Sent: Tuesday, February 05, 2002 8:03 PM To: usr-tc(a)lists.xmission.com Subject: Re: [USR-TC] Forcing a default route for customer through radius Also sprach Brian Becker >Is there an attribute to force a default route other than the normal >via radius for a particular customer? Check into the Internet Equal Access (IEA) feature. Basically let's you set up per-user default routes. I've not used this feature personally, so I don't know how much help I can be on configuration issues, but I know that's what it does. :) Another option might be to configure the customer as a tunnel user and tunnel them to wherever you need to get their traffic, though there are, obviously, some complications from that. -- Jeff McAdams Email: jeffm(a)iglou.com Head Network Administrator Voice: (502) 966-3848 IgLou Internet Services (800) 436-4456 _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

6 9

RE: [USR-TC] HELP: Lightning HiPerDSP
by support＠inet2000.com 16 Dec '02

16 Dec '02

We've been trying to... but some of the wording is different, and it's different than the TelCo's wording again, so they're not a lot of help on knowing how our equipment should be set. Are you saying that the eAndMTypeII is the same as linkEMImmediateStart? On 9/5/02 12:38 PM, USR-TC(a)MAILMAN.XMISSION.COM wrote to SUPPORT: -> Try changing the setting on the DSP DialTrnkType: loopStart to EAndM Type II -> -> At the very least you should configure the DSP to these same settings that -> worked for you on your other gear. -> -> Todd -> -> -----Original Message----- -> From: usr-tc-admin(a)mailman.xmission.com -> [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of -> support(a)inet2000.com -> Sent: Thursday, September 05, 2002 2:04 PM -> To: usr-tc(a)mailman.xmission.com -> Subject: Re: [USR-TC] HELP: Lightning HiPerDSP -> -> -> The other equipment has some differences and some different wording for the -> settins. It lists.... -> -> Line Type : dsx1ESF -> Coding : dsx1B8ZS -> RecEqualiz: linkRxEqualizerOff -> LineBuildOut: t1Pulse0dB -> fd1: : Ansi-T1-403 -> Mode: : robbedBit -> robbedbitprotocal: linkEMImmediateStart -> MessageOrientedSwitchType: ni1 -> NFAS InterfaceID: 0 -> NFAS Primary WAN: 1 -> Loobackconfig: NoLoop -> SendCode: SendNoCode -> -> So, as far as we can tell, the settins are the same on everything they cross -> over on... We're just really stumped here. -> -> Are there settings in the ARC or NMC that can cause a dead air answer? -> -> On 9/5/02 11:57 AM, USR-TC(a)MAILMAN.XMISSION.COM wrote to SUPPORT: -> -> -> -> -> > We get the same results on two different DSP cards, yet the T1 works on -> our -> -> > old backup equipment, so it must be OK. -> -> Why not get the proper line settings from the old equipment and use -> those? -> -> -- -> -> Lewis Bergman -> -> Texas Communications -> -> 4309 Maple St. -> -> Abilene, TX 79602-8044 -> -> 915-695-6962 ext 115 -> -> -> -> _______________________________________________ -> -> USR-TC mailing list -> -> USR-TC(a)mailman.xmission.com -> -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> -> -> -> _______________________________________________ -> USR-TC mailing list -> USR-TC(a)mailman.xmission.com -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> -> -> -> _______________________________________________ -> USR-TC mailing list -> USR-TC(a)mailman.xmission.com -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 2

Total Control Manager/SNMP
by Sysop 02 Dec '02

02 Dec '02

Hi, I want to do some lab experiments with the used hiper arc system. However, there's no 3Com's software available with me for the snmp management. I want to control the unit other than CLI. Can anyone provide me a link to download the TCM/SNMP for HiperARC. Or if there's any other NMS that is capable of managing the HiperARC with all of TCM's functions, please let me know the download link. thanks .. kernel4x

4 4

Anybody interested in an USR Total Control Hub?
by Martin Oberle 27 Nov '02

27 Nov '02

I have for sale: USR Total Control Hub (manufactured in 1997) with PRI-Card, 7 Quad modem card, NMC, WAN-Card.... It is completely working. If you are interested I can send you more details. Martin Oberle moberle(a)gmx.de -- +++ GMX - Mail, Messaging & more http://www.gmx.net +++ NEU: Mit GMX ins Internet. Rund um die Uhr fÃ¼r 1 ct/ Min. surfen!

1 0

Channelized T1 in a DSP
by WayneG 27 Nov '02

27 Nov '02

Anyone using a Channelized T1 into a DSP? We have a TC boxes with PRI's into the DSP's running no problem. But in this location we are using a T1 (no PRI tarriff) and cannot get the TC to accept a call. It rings, 3 seconds of silence and then busy. I have swapped complete chassis and all cards, and reset everything to defaults and reconfigured. I have a feeling that there is some setting in the ARC that I am missing that is different between a T1 and a PRI (like modem mapping or something??) I changed the DSP card from "Message Oriented" to "Bit Robbed." But everything else is the same as our PRI chassis. Help??? Wayne Griswold (906) 774-4847

4 3

no downloads on connecting to total control
by Jerome 27 Nov '02

27 Nov '02

I have a 3com total control hub with 8 DSP cards. Its been running ok for quite a while, but, recently it allows subscribers to connect but they don't get downloads from the Internet at all. Does anybody know the cause of this and how it can be solved. I am desperate and seriously need help. Jerome --------------------------------- Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now

2 1

RE: [USR-TC] Channelized T1 in a DSP
by Joel - Fox Computers 26 Nov '02

26 Nov '02

I found Line Interface Options, but don't have a "Line Interface Source" option on mine. Where do you find that? -----Original Message----- From: eric(a)dol.net [mailto:eric@dol.net] Sent: Tuesday, November 26, 2002 10:45 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Channelized T1 in a DSP The modems themselves need to be told to use the t1 card and not be set to use the pri Under line interface options set the line interface source to be t1 not pri eric >I'm using CT1's with DSP's - copy and paste me your Trunk Settings and I'll try to help. > >- Joel > > >-----Original Message----- >From: WayneG [mailto:WayneG@uplogon.com] >Sent: Tuesday, November 26, 2002 9:32 PM >To: usr-tc(a)mailman.xmission.com >Subject: [USR-TC] Channelized T1 in a DSP > > > Anyone using a Channelized T1 into a DSP? We have a TC boxes with PRI's >into the DSP's running no problem. But in this location we are using a T1 >(no PRI tarriff) and cannot get the TC to accept a call. It rings, 3 >seconds of silence and then busy. > I have swapped complete chassis and all cards, and reset everything to >defaults and reconfigured. I have a feeling that there is some setting in >the ARC that I am missing that is different between a T1 and a PRI (like >modem mapping or something??) I changed the DSP card from "Message >Oriented" to "Bit Robbed." But everything else is the same as our PRI >chassis. > > Help??? > >Wayne Griswold >(906) 774-4847 > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] Channelized T1 in a DSP
by eric＠dol.net 26 Nov '02

26 Nov '02

The modems themselves need to be told to use the t1 card and not be set to use the pri Under line interface options set the line interface source to be t1 not pri eric >I'm using CT1's with DSP's - copy and paste me your Trunk Settings and I'll try to help. > >- Joel > > >-----Original Message----- >From: WayneG [mailto:WayneG@uplogon.com] >Sent: Tuesday, November 26, 2002 9:32 PM >To: usr-tc(a)mailman.xmission.com >Subject: [USR-TC] Channelized T1 in a DSP > > > Anyone using a Channelized T1 into a DSP? We have a TC boxes with PRI's >into the DSP's running no problem. But in this location we are using a T1 >(no PRI tarriff) and cannot get the TC to accept a call. It rings, 3 >seconds of silence and then busy. > I have swapped complete chassis and all cards, and reset everything to >defaults and reconfigured. I have a feeling that there is some setting in >the ARC that I am missing that is different between a T1 and a PRI (like >modem mapping or something??) I changed the DSP card from "Message >Oriented" to "Bit Robbed." But everything else is the same as our PRI >chassis. > > Help??? > >Wayne Griswold >(906) 774-4847 > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >

1 0