September 2001 - USR-TC - mailman.xmission.com

RE: (usr-tc) NMC not responding
by Mark E. Levy 06 May '03

06 May '03

I;ve had this happen a few times. Just reboot the NMC card by sliding it out if the chassis or via the console interface and it will be well again (until next time). Rebooting the NMC won't affect active users sessions. --------------------------------------------------------------------- Mark E. Levy, President FSInet, Inc. | System Management Associates, Inc. 800-827-6085 x202 | 847-291-1550 x202 847-753-6832 fax | 847-291-3866 fax www.fsi.net | www.sysman-inc.com mark(a)fsi.net | levy(a)sysman-inc.com --------------------------------------------------------------------- > -----Original Message----- > From: Jeff Mcadams [mailto:jeffm@iglou.com] > Sent: Friday, June 08, 2001 9:51 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) NMC not responding > > > Also sprach Kirk Mitchell > > My NMC recently stopped responding to SNMP queries, etc and I'm > >unable to access it via TCM. It has, however, not seemed to affect > >anything as far as dial-up, routing, etc. Other than the fact that I > >can't run MRTG against it or the badmodems.pl script, there's no > >indication that it's having problems. > > Not surprising. The NMC does not have anything to do with the routine > actions of taking and handling calls...it is what it says it > is...purely > a management card. You can totally remove the NMC and not lose any of > the actual *production* functionality of the chassis. > > > Has the card gone bad...need replaced, lost something in part of > >config? How do I go about finding/fixing the problem? > > Proly just needs a reboot, or possibly a reconfig...I've had > a few lose > some of the config (including IP addresses and stuff), and a reconfig > from console (takes me about 30 seconds these days) gets them > fully back > up and running (sucks if its a remote city though). > -- > Jeff McAdams Email: jeffm(a)iglou.com > Head Network Administrator Voice: (502) 966-3848 > IgLou Internet Services (800) 436-4456 > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

(usr-tc) FW: [datacomm] Secret access to TCs
by Brian Becker 24 Jun '02

24 Jun '02

The newest edition to our IT Department (he's been in Tech Support for 3 years) emailed me this afternoon (full email below). I didn't believe him at first so I telneted to on of our TC boxes and when prompted with "Login:" I typed adm and pressed Enter. HOLY COW! It said "Hiper:" and I had full access. I'm curious as to how many people on this list were vulnerable like us (we have 20 TC boxes throughout Southeast Missouri). Brian Brian Becker President, Poplar Bluff Internet, Inc. P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114 Home of http://semo.net - Southeast Missouri's Online Community http://TotallyFabricated.com Total Scrutinizer - Tech Support Just Got Easier WebGabber - All-html Web Chat Software -----Original Message----- From: Adam Barnhill Sent: Tuesday, July 24, 2001 6:41 PM To: ---interoffice DataComm List--- Subject: [datacomm] Secret access to TCs It has come to my attention that our TCs were vulnerable to anyone's attack. User : adm Would allow access to manage and login to our TCs. The fix was easy. Just 'del user adm' and then 'save all' (thanx Brian) I was actually searching for TC command references, and happened upon ;) a hack list of default and backdoor passwords. The link I originally found a hack article on is http://the.wiretapped.net/security/info/textfiles/k1ine_11.txt and the password list is in that tree somewhere.. Lots of backdoors for other RAS, switches, hubs and other.. Adam Barnhill Systems Technician / IT Dept. Semo.net / Poplar Bluff Internet, Inc. 1(877)686-9114 http://semo.net/ _______________________________________________ datacomm mailing list datacomm(a)lists.semo.net http://lists.semo.net/mailman/listinfo/datacomm - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

(usr-tc) Upgrading a TC
by Rob 19 Jan '02

19 Jan '02

What is the *least* expensive way to upgrade a TC v34 system to v90? Is there one? Feel free to write me offlist at mailto:rjb@worldnetoh.com. Thenks! Rob - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3

(usr-tc) problem converting from CT1 to PRI
by Randy McMillan 11 Oct '01

11 Oct '01

We have several TC chassis with quad modems that we want to convert to PRI. One of chassis has a DSP (2.1.9) card that works fine with a PRI. They all have HyperArc with 5.0.99 software. The process I went through on a chassis was to load the current PRI software on the T1/PRI card, and set the trunk setting b8zs,esf, switch type 5ess, (although I believe they have a CTI switch). The other settings match (dnis,eandmtypeII, wink, etc) the CT1 settings. Then on the Quad modems I set the "Line Interface Source" from t1Tdm to priTdm. Save and reboot. When everything is connected, I have all green lights, and the switch guy sees the d channel come up. When we dial into that line, the switch guy sees the call come in on the first trunk but the modem doesn't answer. I don't see any lights flash on the modem card to indicate a call coming in. The default config on the PRI card is round robin allocation of modems as opposed to fixed assignment which I didn't change. The DSP card is using fixed assignment routing. If the switch guy converts it back to a CT1, and I load the CT1 software back in, and switch the line interface source on the quad cards, then it works fine. Can anyone tell me what I am missing, or point me in a direction to look? Thanks. Randy McMillan PacInfo - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 3

(usr-tc) ARC not denying logins
by Paul Farber 28 Sep '01

28 Sep '01

hello all I have rather strange problem. My RADIUS server is rejecting the authentication requests... but the ARC's (two of them) are letting users on online. The user in question is NOT in the users table. The same RADIUS server is working 'correctly' with PATTON 2800's and 2996's (you cannot connect with the 'disabled' accounts). For a starter here is sho radius RADIUS SETTINGS Fill Null Attributes : DISABLED Attribute Style: STANDARD Authentication Algorithm: ROUND_ROBIN Interim Accounting Interval Status: DISABLED Interim Accounting Interval: 240 seconds IEA Radius Source Port Authentication ENABLED IEA User Radius supplied username DISABLED Send Unauthenticated STOP record ENABLED Send Accounting records for default user: ENABLED Report Acct IP Addr only for Primary Link: DISABLED Send only STOP Acct for failed services: DISABLED Test the authentication locally via radtest: radtest jericho xxxxx localhost s1 xxxxx Sending request to server localhost, port 1812. radrecv: Reply from host 127.0.0.1 code=3, id=84, length=20 Access denied. yet TC gives me: HiPer>> _auth jericho xxxxx CLI - User: jericho is Authenticated But the radius server records the denial: Wed Sep 26 18:27:16 2001: Auth: unix_pass: [jericho]: invalid shell Wed Sep 26 18:27:16 2001: Auth: Login incorrect: [jericho/xxxxx] -- Paul Farber Farber Technology farber(a)admin.f-tech.net Ph 570-628-5303 Fax 570-628-5545 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 6

(usr-tc) FS: 48 Port Chassis
by Marshall Morgan 27 Sep '01

27 Sep '01

2 Chassis like the following: =================== 1 Dual T1 (CT1/PRI) Card 12 Digital Quad Modems 1 HiperARC w/64 Megs 1 NMC (x2/v90) enabled w/16-20 Megs 1 70A AC Power Supply TOTAL SHIPPED (Contential US) = $2500.00 Additional 70A PS = $250.00 TCM 8.0.10 included. Will configure, deliver and warranty for 90 days. Free basic support. Just came out of service. Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) 486 Hiper NMC question
by Mitch Dailey 26 Sep '01

26 Sep '01

Does anyone know if the 486 Hiper NMC's came with v.90 enabled or was that an optional feature? Mitch Dailey NileNet, Ltd. mtd(a)nilenet.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 4

RE: Re: (usr-tc) Quad v34 Modem Cards
by notuteye＠mail.ucomgh.com 26 Sep '01

26 Sep '01

Patric Thanks for the response, it seems to have cleared the initial problem. Now I'm faced with the fact that the modems seem to work in some slots but not in others. For instance, if I put a modem into slot 1 or slot 2, it works fine, but putting the same modem card and NIC into slot 11 doesn't produce any result. What is going on? Is there a chassis config command I've neglected?? Original Message: ----------------- From: Patrick C. Wolf pwolf(a)sdc.org Date: Tue, 25 Sep 2001 07:22:51 -0600 (MDT) To: usr-tc(a)lists.xmission.com, usr-tc(a)xmission.com Subject: Re: (usr-tc) Quad v34 Modem Cards Are you using them in analog mode or digital? If analog, using the Total Control Manager, make sure that you have elected the input source to be from the NIC, not the TDM bus. Alternately, if digital, make sure you have the input source the TDM bus and not the NIC. Pat On Tue, 25 Sep 2001, notuteye(a)mail.ucomgh.com wrote: > Hi > I am having a really major problem here. I now have TWO total control chassis, and my quad analog/digital modems will not respond to incoming calls in either. Is there something I'm not doing? Can anybody help ? > > -------------------------------------------------------------------- > mail2web - Check your email from the web at > http://mail2web.com/ . > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > -- ----------------------------------------------- Patrick C. Wolf SDC Internet pwolf(a)sdc.org 722 N California Suite 4 (505) 838-1620 Socorro, NM 87801 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. -------------------------------------------------------------------- mail2web - Check your email from the web at http://mail2web.com/ . - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) FS: USR/3COM Total Controls - Hiper nmc, arc, dsp,
by ISP-NetworkHardware.com 26 Sep '01

26 Sep '01

Partial Listing...All in stock. Prices negotiable within reason. WTB: (STANDARD) USR NMC v90 enabled Want to Sell: Hiper NMC sets $1000 Hiper DSP sets $1400 Hiper ARC sets 64MB $1200 MultiSpan 96port DSP sets (NEW) $11,999...Best price on market! Hiper Bundles - HD Chassis with 70A power NMC Hiper ARC 2x Hiper DSP $5000 Quad Bundles - Classic chassis with dual 45a power nmc non v90 netserver card 12x analog/digital modem sets dual pri/t1 $1100 Netserver PRI $200 Dual PRI $200 NMC non v90 $200 All flavors of quad modems...shott me an email if your interested. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) Quad v34 Modem Cards
by notuteye＠mail.ucomgh.com 25 Sep '01

25 Sep '01

Hi I am having a really major problem here. I now have TWO total control chassis, and my quad analog/digital modems will not respond to incoming calls in either. Is there something I'm not doing? Can anybody help ? -------------------------------------------------------------------- mail2web - Check your email from the web at http://mail2web.com/ . - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1