June 2001 - USR-TC - mailman.xmission.com

RE: (usr-tc) NMC not responding
by Mark E. Levy 06 May '03

06 May '03

I;ve had this happen a few times. Just reboot the NMC card by sliding it out if the chassis or via the console interface and it will be well again (until next time). Rebooting the NMC won't affect active users sessions. --------------------------------------------------------------------- Mark E. Levy, President FSInet, Inc. | System Management Associates, Inc. 800-827-6085 x202 | 847-291-1550 x202 847-753-6832 fax | 847-291-3866 fax www.fsi.net | www.sysman-inc.com mark(a)fsi.net | levy(a)sysman-inc.com --------------------------------------------------------------------- > -----Original Message----- > From: Jeff Mcadams [mailto:jeffm@iglou.com] > Sent: Friday, June 08, 2001 9:51 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) NMC not responding > > > Also sprach Kirk Mitchell > > My NMC recently stopped responding to SNMP queries, etc and I'm > >unable to access it via TCM. It has, however, not seemed to affect > >anything as far as dial-up, routing, etc. Other than the fact that I > >can't run MRTG against it or the badmodems.pl script, there's no > >indication that it's having problems. > > Not surprising. The NMC does not have anything to do with the routine > actions of taking and handling calls...it is what it says it > is...purely > a management card. You can totally remove the NMC and not lose any of > the actual *production* functionality of the chassis. > > > Has the card gone bad...need replaced, lost something in part of > >config? How do I go about finding/fixing the problem? > > Proly just needs a reboot, or possibly a reconfig...I've had > a few lose > some of the config (including IP addresses and stuff), and a reconfig > from console (takes me about 30 seconds these days) gets them > fully back > up and running (sucks if its a remote city though). > -- > Jeff McAdams Email: jeffm(a)iglou.com > Head Network Administrator Voice: (502) 966-3848 > IgLou Internet Services (800) 436-4456 > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

(usr-tc) Upgrading a TC
by Rob 19 Jan '02

19 Jan '02

What is the *least* expensive way to upgrade a TC v34 system to v90? Is there one? Feel free to write me offlist at mailto:rjb@worldnetoh.com. Thenks! Rob - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3

(usr-tc) 3COM
by Lists 05 Sep '01

05 Sep '01

Anyone know if people like Krish are still on this list, or what their e-mail might be? - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

10 21

(usr-tc) Total Control Program
by Paul M. Ledbetter 04 Jul '01

04 Jul '01

Hello all. I am new to this list and have recently started helping out a associate ISP that has TC boxes and TC programs to handle the boxes. I have looked through the recent archives, but could not find the answers to my basic (and probably stupid) questions. These are older TC boxes running TC Radius on an older NT server. I recently upgraded their main server to a new Dell box with 2000 and installed Access to handle the DB, but apparently they cannot find the original TC programs :-| Does anyone know where I can get a copy of the programs so that I can get the new server up and running? I have looked all over for a source but have had no luck as of yet and I am not too keen on calling 3COM, yet.... Thanks in advance for any help on this. I am new at the TC stuff as I have been running Ascend boxes with Emerald for years so my expertise lies in that arena so far :-)) Paul M. Ledbetter - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 6

(usr-tc) Quad Analog Modem Problems
by Aaron Daniels 02 Jul '01

02 Jul '01

Hi, I am having problems with some Quad Analog modem cards that I have installed, I cannot get them to stay active I do set modem s49 active and it all appears to work, then I save and reset then I get whats below. the modems report A/I/P then after a reset they go A/A/P but I cant get them A/R/P. Basically the modem is not active because it cannot successfully negociate with the packet bus(I think). after a reset my syslog reports: Apr 28 14:05:19 dialup9.dataheart.net S49 packet bus handle opened. Handle = 26. After this the netserver reports the modem as active all though there is still no HDLC Framing and the interface is still set to Unassigned instead of ptp49 as it usually is. then 30 seconds later: Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus failed to connect! stat=-1 Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus handle closed. now the netserver reports it as inactive again. I have Quad Digital/Analog cards working fine in the same chassis but these Quad Analogs are just not co-operating. any help would be appreciated, the 3com knowledgebase has not helped me. Thanks, Aaron Daniels - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 3

(usr-tc) ARC Host Address
by Brian 30 Jun '01

30 Jun '01

I just recently changed the addressing of my ARC's and I am having a problem. It shows one address in "show ip settings" that differs from whats set on eth:1: HiPer>> show ip setTINGS IP System Host Address: 208.206.76.40 IP Forwarding ENABLED IP Address Pool Filtering DISABLED IP Address Pool Round Robin: ENABLED HiPer>> show ip netwORK ip SHOW IP NETWORK ip SETTINGS: Interface: eth:1 Network Address: 207.254.193.69/28 Frame Type: ETHERNET_II Status: ENABLED Reconfigure Needed: FALSE Mask: 255.255.255.240 Station: 207.254.193.69 does anyone have any idea where the 208.206.76.40 could be set at? its not pingable, but its what is passed to pp clients when they do PPP negotiation. I checked all the application_source_address settings and its not set there Brian ----------------------------------------------- Brian Feeny e:signal@shreve.net CCNP+Voice/ATM/Security p:318.222.2638x109 CCDP f:318.221.6612 Network Administrator ShreveNet Inc. (ASN 11881) - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 3

(usr-tc) FS: 3Com Hiper DSP card Sets $1850
by ISP-NetworkHardware.com 29 Jun '01

29 Jun '01

Hello Folks...Good deal here...Still have some left....going fast 5- Hiper DSP card sets $1850ea Includes DSP nac and nic. 4- Hiper ARC $1000 64MB 30 day warranty. Get them while they last. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) Data over voice ISDN calls
by RickL＠solunet.com 28 Jun '01

28 Jun '01

Thanks Jeff...I'll research it some more. In the meantime, anyone else using this implementation for doing ISDN DOV calls? Rick Rick Louizos Solunet Soluserve TAC Manager 1571 Robert J. Conlan Blvd. suite 110 Palm Bay, Fl. 32905 Phone Numbers: Phone: (888)449-5766 / Fax: (407)676-0809 Internet Addresses: mailto:RickL@solunet.com / http://www.solunet.com -----Original Message----- From: Jeff Mcadams [mailto:jeffm@iglou.com] Sent: Thursday, June 28, 2001 11:57 AM To: usr-tc(a)lists.xmission.com Subject: Re: (usr-tc) Data over voice ISDN calls Also sprach RickL(a)solunet.com >Anyone out there in TC-HUB land know if the TC-HUB supports Data over >Voice ISDN calls? I understand the Lucent Portmaster 3 does, and the >Ascend Max does, but in trying to fork-lift some Portmasters out of one >of my customers network, and introduce the TC-HUB, we have discovered >that this feature does not work by default, and can not find any >documentation to help enable it. Anyone know if the TC-HUB supports >this feature and what needs to be done to get it accepting these types >of calls? If I remember correctly, yes, it does support it, but not seamlessly. PM's and Max'es will auto-detect whether the call is voice, data, or data over voice. The TC's, if I understand it correctly, could only do data over voice if its told to do it by called number id or something like that. Basically, you can tell it to do data over voice by assigning a new phone number to your hunt and using that number for a data over voice number. Then when calls come in to that number, the TC will answer with data over voice. I have never done data over voice, but that's how it was described to me back in the day (its been a couple of years since this topic came up I believe) -- Jeff McAdams Email: jeffm(a)iglou.com Head Network Administrator Voice: (502) 966-3848 IgLou Internet Services (800) 436-4456 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Data over voice ISDN calls
by RickL＠solunet.com 28 Jun '01

28 Jun '01

Anyone out there in TC-HUB land know if the TC-HUB supports Data over Voice ISDN calls? I understand the Lucent Portmaster 3 does, and the Ascend Max does, but in trying to fork-lift some Portmasters out of one of my customers network, and introduce the TC-HUB, we have discovered that this feature does not work by default, and can not find any documentation to help enable it. Anyone know if the TC-HUB supports this feature and what needs to be done to get it accepting these types of calls? Just FYI: some telcos charge by the minute for Data over ISDN (64k) calls, but charge a flat rate for Data over voice (56K) ISDN calls. This is the reason this feature is important to some customers I think some people use the dial back feature to avoid these tarrifs. sincerely, Rick Rick Louizos Solunet Soluserve - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) need pri/t1 card sets
by eric＠dol.net 28 Jun '01

28 Jun '01

Some of the problems I have been having with some t1s and pris I have is due to faulty cards. Does anyone have some nic and nac sets, preferably pri cards, since they go either way, to sell? I would like them asap. I don't want to buy chassis just to get pri cards. thanks eric - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0