May 2016 - montgomery_boats - mailman.xmission.com

M-15 for Sale in Minneapolis, MN
by Chee Pang Chua 17 May '16

17 May '16

My M-15 is for sale. Owned it for 6 years, upgraded to M-17. See link for details http://minneapolis.craigslist.org/hnp/boa/5585859936.html

1 0

M-12 for sale Phx.area
by GILASAILR＠aol.com 15 May '16

15 May '16

came across this yesterday - Montgomery 12 sailboat with Evinrude 2hp http://phoenix.craigslist.org/evl/boa/5565943255.html can do a 'drive by' if interested in another set of eyes - mid to late week. GO

2 1

M-10 - when it rains...dinghy week in central AZ.
by GILASAILR＠aol.com 15 May '16

15 May '16

Montgomery 10 sail/row boat http://phoenix.craigslist.org/nph/boa/5523718521.html GO

1 0

Bellingham anyone?
by Jazzy 11 May '16

11 May '16

Hi all, I find myself in Bellingham for most of the day. Any Montys around I could peek at? Jazz

1 0

Selling my Tohatsu SailPro 6hp
by John Schinnerer 10 May '16

10 May '16

In case anyone wants to overpower their M-17 - or would be great for an M-23 or any other larger "second boat" anyone might have: http://medford.craigslist.org/bpo/5578109518.html cheers, John S. -- John Schinnerer - M.A., Whole Systems Design -------------------------------------------- - Eco-Living - Whole Systems Design Services People - Place - Learning - Integration john(a)eco-living.net - 510.982.1334 http://eco-living.net http://sociocracyconsulting.com

1 0

My M15 TwoCan is up for sale
by ndorf＠surfbest.net 03 May '16

03 May '16

1985 Jerry-built M15. Offwhite hull with green sheer stripe. Pineapple Main & lapper jib, both really should be replaced. I also have the original McKibbin sails (for sizing). I have owned this boat for about 5 years or so. Since that time I have removed and rebedded the mast tabernacle, and most of the jamb cleats. I have one extra rudder blade that JO Woodworks made for me, plus the original. Tiller has Ronstan battlestick and Tiller Clutch. 2 danforth-style anchors. Normal cosmetic wear for a boat of this age. She does not have the CB rust disease. The only time the CB stuck was a couple of times when I beached her and pebbles got in there. was able to crawl underneath and hose out. All lines run aft to the cockpit. That includes a block on the bow through which you can run a jib downhaul, or use that same line to attach to the Jib halyard shackle to facilitate raising & lowering the mast singlehanded. Outboard is a Yamaha 4hp, circa 1992. Runs fine. 2-cycle, 100:1 ratio. Trailer is OK, needs occasionally touch up paint to keep rust from forming. Boat is in my garage in the Sacramento area. I am selling because I am moving in several weeks to the East Coast and would prefer not to drag the boat cross country. But if she doesn't sell before May 21st, she's coming along for the ride and then she's stuck with me ;-) My house is sold and I have to be out on May 22nd to begin my cross country trek. You can find the listing on Sailboatlistings.com, or pm me on the TrailerSailor Monty board. If you search on TwoCan you'll find a sufficient number of photos of her. This is the boat that ran the Cruiser Challenge in less than 12 parsecs. Well hardly, but with a new suit of sails and a capable skipper she has great potential. -Neil -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

4 3

New boat
by Janice Smith 03 May '16

03 May '16

Hello fellow sailers, Just bought M15 number 365. I'am in White Salmon Wa. and the boat is in Nancy Ky. I've been looking for a while and this had what I wanted. Recent sails, motor, trailer, rig, etc. The boat looks really clean and the owner is a good guy. Can you spell " ROAD TRIP ". We've been wanting to do a trip in the in the boosted Ford Flex so here we go. I'll post again when we get back. Sent from my iPad

5 4

Trailer roller axles
by Thomas Buzzi 01 May '16

01 May '16

FYI, Just installed five boat trailer rollers in the bunkboard that my Monty 17 keel slides on. Now it rolls on and off the trailer with just the port and starboard bunk boards rubbing on the hull. Discovered that the "Pal Nuts" that come with the 5/8 inch diameter axles are an iffy product to use. Had several of them tapped onto the ends of some of the axles. They were all the way on, about 1/2 inch worth of axle inside. Then happened to pull on one to see how well it grabbed the metal axle. It came right back off in my hand. Went on to check all of them and about half were just sitting there just waiting to come off and allow the spinning axle to unscrew itself and dump my beautifully restored keel down onto the metal braces for the rollers. Ouch. Ended up removing all the "Pal(?) Nuts" and drilled all the axles for 1/8 inch ss. cotter pins on washers at each end. This year's "shake down cruise" is fast approaching. Fair winds, Tom B <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campai…> Virus-free. www.avast.com <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campai…> <#DDB4FAA8-2DD7-40BB-A1B8-4E2AA1F9FDF2>

1 0

Msgs
by George Iemmolo 30 Apr '16

30 Apr '16

I know it is sailing weather in many parts of the country and that might be why I have not seen a MSG. on the Wrinkle Boat list for a few weeks or somehow I was dropped? Still working on getting the Jib Furling system assembled and the rest of the boat ready to splash. docks are in so it's up to me now.😎 Hello out there anyone home?😀 George "We Can Not Control the Wind But We Can Adjust Our Sails"

8 12